Conference Abstracts

Abstract

POSTER One of the critical elements of water resource management is the dynamic exchange between groundwater and surface water. Quantifying this exchange strongly relies on an adequate characterisation of the lithological architecture of the involved aquifer system. In the past, this characterisation often relied on lithological data obtained through invasive methods. However, given the spatial heterogeneity of the subsurface, these methods do not provide the density of sampling required for an accurate ‘‘image’’ of the large‐scale architecture of the aquifer system, leading to large uncertainties in the variations and continuities of subsurface structure. These uncertainties inevitably lead to inaccuracies in the conceptual geohydrological model, thereby diminishing the prospects of an accurate assessment of the groundwater–surface water interaction. In order to limit the uncertainties, the results of electrical resistivity tomography (ERT) surveys conducted on a  site  near  the  Krugersdrift  Dam in the Free State Province of South Africa  were used to make inferences   regarding  the   prevailing  geohydrological  conditions.  The   resistivity  models   were compared to borehole logs from existing boreholes to produce a refined model of the subsurface architecture related to groundwater–surface water interactions.

Abstract

Gold mining  activities over  the  past 60 years  in the Klerksdorp  goldfield produced  saline mine drainage that polluted water. Oxidation of sulphide material in tailings storage facilities, waste rock dumps and extraction plants is mobilised to produce saline mine drainage with sulphate, minor salts and  metals  that  seep  to  the  groundwater  and  ultimately  into  surface  water  resources.  Water regulation requires mines to prevent, minimise/reduce or eliminate pollution of water resources. The waste philosophy has matured from tolerate and transfer to treat and termination of pollution sources.  The  impact  of  the  pollution  was  determined  and  possible  technologies  to  treat  the impact   were   evaluated.   Source   controls   with   proper  water  management  by  storm  water management,  clean  dirty  water  separation,  lined  water  conveyance  structures  and  reduced deposition of water on waste facilities are crucial. The aquifer character determines the possible remediation technology. From the possible technologies phytoremediation, physical interception and  re-use  of  this  water  was  selected.  In  future  possible  treatment  of  the  water  would  be considered. This paper explain the strategy and report on the phased implementation of these plans and the expected results. The establishment of 500 ha of woodlands as phytoremediation, interception trenches of 1 000 m, 38 interception boreholes and infrastructure to re-use this water is planned. The total volume of 15 Ml/day would be abstracted for re-use from the boreholes and trenches. The woodlands can potentially attenuate and treat 5 Ml/day. The established woodlands of 150 ha prove to be successful to intercept diffused seepage over the area of establishment and reduce  the  water  level  and  base  flow.  The  two  production  interception  well- fields  that  are abstracting  50  and  30 l/s,  respectively  , indicate  a  water  level decline of between 2 to 14 m, with regional cones of depression of a few hundred meters to intercept groundwater flow up to a 20 m depth. Predictions from groundwater modelling indicate that these schemes can minimise pollution during the operational phase and protect downstream water resources. Predictions from modelling indicate that the pollution sources need to be removed to ensure long-term clean-up to return the land to safe use. The gold and uranium prize is securing the removal of the sources through  re-processing  of  the  tailings  and  waste  rock  dumps.  After  removal  of  the  sources  of pollution,  the  remediation  schemes  would  have  to  be  operated  for  20  years  to  return  the groundwater to an acceptable standard  of  stock  watering  and  industrial  water  use.  The  water quality is observed by a monitoring network of approximately 100 observation boreholes.

Abstract

The Paleozoicage Natal Group Sandstone (NGS) that outcrops from Hlabisa (in the north) to Port Shepstone (in the south) and Greytown (west) to Stanger (east) in the Province of KwaZulu-Natal, South Africa, is investigated in terms of its hydrogeological characteristics. This sandstone group, which comprises a lower Durban and an upper Marrianhill Formations, is a secondary/fractured aquifer system that has variable but good productivity across its members. It is characterised by variable borehole blow yields ranging from 0.2 l/s to as high as 20 l/s, with more than 50% of the boreholes having blow yield > 3 l/s. Preliminary analysis of these boreholes yields indicates that higher yielding boreholes are associated with a network of intersecting fractures and faults, and are recommended targets for future water well-siting in the area. Groundwater in the NGS is of good quality in terms of major and trace element composition and it has a total dissolved solids (TDS) composition of <450 mg/l. It was observed that the specific electrical conductivity (EC), TDS and major ions composition of groundwater within the sandstone decrease from north to south, which appears to be controlled by the geochemical composition of the aquifer material and an increase in the rate of recharge. Depth to groundwater is also found to decrease southwards because of an increase in the rate of recharge. Groundwater hydrochemical facies are generally either Na-HCO3 or Na-HCO3–Cl, and environmental isotope data (2H, 18O, Tritium) indicates that the groundwater gets recharge from modern precipitation. Furthermore, the EC increases from inland to the coastal zone, indicating maritime influences and the general direction of groundwater flow is eastwards, to the Indian Ocean.

Abstract

The Department of Water Affairs (DWA), Chief Directorate: Resource Directed Measures has developed guidelines over the past decade  in order  to  facilitate  proper implementation of the Groundwater   Resource   Directed   Measures   (GRDM)   (also   known   as   determination   of   the groundwater component of the Reserve). An intrinsic component of the GRDM is delineation of Integrated Units of Analysis (IUAs) from which the allocatable groundwater and surface water components are calculated, which essentially drives the allocation of water use licenses. Delineation typically follows a three-tiered approach, namely primary, secondary and tertiary level. Primary delineation is based on quaternary boundaries (considered to be the basic building block of the IUA); secondary follows geological, hydrogeological and hydrological boundaries, groundwater abstraction zones and baseflow contribution; and tertiary is dependent on management criteria. How then, do we undertake this challenging task of delineating IUAs to a level where it can be better managed and monitored? Complexities arise when hydrogeological data are scarce, hydrological and hydrogeological systems are not in sync, aquifers extend across a quaternary, water management area, provincial and administrative boundaries, surface water and groundwater interactions are not well understood, and legislation on protection of water resources differs greatly from one country to the next. Having undertaken delineation of IUAs in the Waterval Catchment (Upper Vaal WMA), Olifants WMA and Mvoti to Umzimkhulu WMA with the available datasets, the key criteria for the respective  WMAs  have  ultimately  been  management  class,  significant  aquifers,  groundwater– surface water interaction and groundwater stressed areas, and secondary catchment boundaries, followed by other hydrogeological, geological and management considerations.

Abstract

Determining   impacts   associated   with   the   production   of   shale   gas   in   the   semi-arid   Karoo   on groundwater is vital to people living in the Karoo. On the one hand shale gas can be a game-changer for energy supply, but on the other it may have a devastating effect on the environment. Knowing the potential  impacts  of  shale  gas  mining  beforehand,  the  government  can  set  appropriate  regulatory protocols  and  tools  in  place  to mitigate  potential  risks.  This paper  describes research  done  on  the potential impact that hydraulic fracturing could have on groundwater in the Karoo. A wild card that only exists in the Karoo Basin of South Africa is the numerous dolerite intrusions. These dolerite structures are associated with relative high-yielding boreholes because of the fractured contact aureole that exist between solid dolerite and the adjacent Karoo sediments. Compromised cement annuli of gas wells are the  major  preferential  flow  paths along which  methane  and fracking fluid  can escape  into shallow, freshwater aquifers. This study focused solely on the impact of compromised cement annuli of gas wells. The Karoo Basin is under artesian conditions which imply that any pollutant will always try to migrate upwards in the Karoo. The hot-water springs in the Karoo indicate that upward velocities of water are relatively high (the spring water take only days to travel from deep down to the surface). The cubic law was  used  to  estimate  potential  upward  leakage  rates  from  gas  wells  (during  production,  but  after cessation thereof as well, when pressures will rebuild  because  of  artesian  behaviour  of  the  Karoo formations).  Potential  leakage  rates  along  faulty annuli of a well can vary between a value close to zero to two liters per second in the case of an aperture of 0,5 mm. These leakage rates were used as input to a 2D numerical groundwater flow and mass transport model. The 2D model was run for 30 years and the movement of pollution from the gas wells on the pad simulated. The model indicates that an area of 300 ha could be contaminated over a period of 30 years in a downstream groundwater flow direction.  If  an  abstraction  borehole  drilled  along  a  fault  zone  or  a  dyke,  intersecting  the  fracked reservoir, is introduced into the model, results predict that the pollutant will reach the borehole in less than two months if the borehole is situated six kilometres from the well-pad. The total impact that fracking will have on the groundwater in the Karoo, is a function of the total area that will be fracked.

The outcomes of this research clearly show that fracking in South Africa cannot be done in the same way than  it  is  currently  done  worldwide.  A  rule  that  will  force  gas  companies  to  disclose  fracking  fluid contents is non-negotiable. Companies should also be required to measure pressures in the fracked gas reservoir after closure. An additional requirement to enforce sealing of the entire fracked reservoir with a very dense material like bentonite or a mud with a very high density to capture the fracking fluids deep down in the gas reservoir should not be negotiable.

Abstract

A multi-data integration approach was used to assess groundwater potential in the Naledi Local Municipality located in the North West Province of South Africa. The geology comprised Archaean crystalline basement, carbonate rocks (dolomite and limestone) and windblown sand deposits of the Kalahari Group. The main objective of the study is to evaluate the groundwater resource potential using multi-data integration and environmental isotope approaches. Prior to data integration, weighting coefficients were computed using principal component analysis.

The results of integration of six layers revealed a number of groundwater potential zones. The most significant zone covers ~14% of the study area and is located within carbonate rocks in the southern part of the study area. The localisation of high groundwater potential within carbonate rocks is consistent with the results of principal component analysis that suggests that lithology significantly contributed to the total data variance corresponding to principal component 1. In other words, carbonate rocks consisting of dolomite and limestone largely account for groundwater occurrence in the southern part of the area. In addition, the relatively elevated isotopic signature of tritium (≥1.0 TU)  in  groundwater  samples  located  in  the  southern  part  of  the  area  suggests  a  groundwater recharge   zone.   Furthermore,   moderate-to-good   groundwater   potential   zones   within   the Ventersdorp lava coincide with maximum concentration of fractures, which is consistent with the results of statistical correlation between borehole yield and lineament density. The multi-data integration approach and statistical correlation used in the context of evaluating groundwater resource potential of the area provided a conceptual understanding of hydrogeological parameters that control the development of groundwater in crystalline and carbonate rocks. Such approach is crucial in light of the increasing demand for groundwater arising from municipal water supply and agricultural use. The two approaches are very effective and can be used as a sound scientific basis for understanding groundwater occurrence elsewhere in similar hydrogeological environments.

Abstract

South Africa currently ranks number nine in the world of the proved coal reserves that has been estimated to last for over 200 years. Coal constitutes about 77% of the primary energy needs in the country, with the Waterberg Coalfield estimated to host about 40% of the remaining South African coal resources. Coal deposits in the study area largely consist of shales, mudstones, siltstones and sandstones which host coal-containing clay minerals; quartz, carbonates, sulphides and the most abundant sulphide mineral is pyrite. Once mining begins, the sulphide minerals are exposed to surface which allows contact with atmospheric oxygen and water causes oxidation to take place, therefore causing acid-mine drainage (AMD). Acid-base accounting (ABA) was used to determine the balance between the acid-producing potential (AP) and acid-neutralising potential (NP). From the analysis the Net Neutralising Potential (NP-AP) was determined, which is one of the measurements used to classify a sample as potentially acid or non-acid-producing. Mineralogical analyses will be done by x-ray defraction (XRD) to define and quantify the mineralogy of the geological samples which can help in the management plan to minimise generation of acid. AMD does not only result in the  generation of acid, but as well as in decreased pH values and increased values of specific conductance, metals, acidity, sulphate, and dissolved and suspended solids. Inductively coupled plasma analysis was done to determine the release of the heavy metals which can be detrimental to the environment. Sample analysis was done on the interburden, overburden as well as the coal samples. From results obtained, over 35% to 50% of the samples have an excess of acid potential which classifies the samples as having a higher risk for acid generation. About 30% to 40% of the samples have a higher neutralising potential; the rest of the samples have a medium acid risk generation. The water demand will increase as developments continue in the  area, with inter- catchment transfers identified as the answer to fill the gap of water scarcity. Acid mine drainage poses a big threat on water resources, both groundwater and surface water nationally, which might be less of a problem in the Waterberg because of the cycle of low rainfall in the area, but the potential of AMD cannot be neglected.

Abstract

Groundwater boreholes are a key element of many mining projects, as part of dewatering and water supply  systems,  and  must  achieve  high  levels  of  operational  efficiency  and  service  availability. Outside of the mining industry, planned borefield maintenance programmes have become a key part of professional well-field management, with proven benefits in terms of operational cost savings and continuity of pumping. However, the benefits of proactive planned maintenance of groundwater boreholes on mine sites have only recently been widely recognised. Potential operational problems are described, including water quality issues which can result in mineral contamination leading to deposits and scale build-up which can clog screens and pumps, reduce water flow and yield, and eventually cause pump breakdowns and mine stoppages. Best practice methodologies to remove or minimise the contamination are described and the benefits of implementing a planned maintenance programme are discussed. Case studies are described from two significant mines in Australia, where boreholes suffered from mineral contamination, including calcium carbonate and iron bacteria contamination. Both mines suffered  from  increased  pump  breakdowns,  groundwater  yields  consistently  below  target  and serious cost overruns. Borehole rehabilitation treatment plans were implemented to resolve the immediate contamination problems followed by an ongoing maintenance programme to prevent or minimise their reoccurrence. Treatment programmes included a downhole camera survey, use of a bespoke software program to review the results of the survey and the available water quality data, and a purpose built rehabilitation rig that included the use of specialist chemical treatments to remove and control the existing encrustation and clogging deposits.

Abstract

Groundwater is not often regarded as ecosystems and especially fractured aquifer systems are seen as organism free. Conventional tests show very little to no presence of micro-organisms in groundwater. However, these micro-organisms are ubiquitous and can be detected by using sophisticated methods. In this specific case study where petroleum hydrocarbon  contamination exists in a fractured rock aquifer, the presence of micro-organisms has been for years inferred by means of monitoring for secondary lines of evidence that prove attenuation of the contaminants, not only by means of dilution, adsorption or diffusion into the matrix, but through metabolism. The sampling evidence is clear that the preferential sequence of metabolism is taking place whereby electron acceptors are reduced as predicted for such biodegradation. Specifically sulphate is consumed and mostly manganese is reduced, with some iron reduction also being observed. Monitoring has shown that  groundwater recharge bringing in  new  nutrients effected increased biodegradation. In order to definitively identify the contribution made by micro-organisms, DNA testing was performed. The results support the secondary lines of evidence. Outside of the contaminated zone very low population numbers of organisms were detected in the groundwater. Inside the contaminated zone elevated population numbers were observed indicating that active biodegradation is taking place. Furthermore, the edges of the plume, where contaminant levels are mostly below detection, contained a more diverse population of micro-organisms than the central area. Conditions on the edge of the plume probably represent an ideal nutrient environment for the organisms as opposed to the high concentration source, which might be toxic to some organisms. Better understanding of the bio-dynamics of this fractured aquifer presents a unique opportunity to better manage and enhance the remediation of the contaminants. Possible strategies include the addition of nutrients when necessary and the cultivation of the naturally occurring organisms to augment the population. The data shows that aquifers are ecosystems even in fractured environments.

Abstract

Abstract

In recent years acid mine drainage (AMD) has become the focus on many mine sites throughout the world. The Witwatersrand gold mines have been the main focus of AMD in South Africa due to their extensive impact on especially groundwater resources. The Witwatersrand Basin is a regional geological feature containing the world-famous auriferous conglomerate horizons. It is divided into sub-basins and the East Rand Basin is one of them. Due to the regional scale of the East Rand Basin AMD issues, a systems approach is required to provide a useful tool to understand the pollution source term and fate and transport dynamics and to aid in environmental decision making and to evaluate the geochemical impact of mitigation measures and evaluate future scenarios.
The numeric geochemical models, using a systems perspective, show that the mine waste facilities, specifically the tailings dams are significant contamination point sources in the East Rand Basin, specifically for acidity (low pH), SO4, Fe, Mn, U, Ni, Co, Al and Zn. When the AMD solution enters the soil beneath the tailings, ferrous and SO4 concentrations remain elevated, while Mn, U, Ni and Co and perhaps other metals are adsorbed. After ~50 years the pollution plume starts to break through the base of the soil profile and the concentration of the adsorbed metals increase in the discharging solution as the adsorption capacity of the soil becomes saturated. The pollution pulse then starts to migrate to the shallow groundwater where contamination of this resource occurs.
Toe seepage from the tailings either first reacts with carbonate, where acidity is neutralised to a degree and some metals precipitated from solution, where after it reaches the surface water drainage, such as the Blesbokspruit, where it is diluted. Some evaporation can occur, but evaporation only leads to concentration of acidity and dissolved constituents, thereby effectively worsening the AMD solution quality. The mixing models have shown that the dilution factor is sufficient to mitigate much of the AMD, although seasonal variability in precipitation and evapotranspiration is expected to have some influence on the mixing ratio and some variability in the initial solution will also be reflected in variation in surface water and groundwater quality.
{List only- not presented}

Abstract

Vapour intrusion (VI) is recognized to drive human health risk at numerous sites that have been contaminated by petroleum products and other volatile contaminants. The risks related to VI are typically evaluated using direct measurement (vapour sampling) or modelling methods. ERM has developed a toolbox approach using a combination of exclusion distance criteria, direct measurement and modelling methods to assess risks and achieve closure. For direct measurement, samples of vapour are taken beneath the floor slab of buildings (sub-slab sampling) or from the air inside the buildings (indoor air sampling). Modelling methods are often used to estimate the partitioning of volatile contaminants from soil or groundwater sources into the vapour phase and the subsequent transport of vapours from the subsurface environment into habitable buildings. A limitation of modelling approaches is that they are designed to be conservative to be adequately protective of sensitive receptors. VI models also do not typically take into account the degradation of hydrocarbon vapours in the presence of oxygen, which has been found to be a significant process for petroleum hydrocarbons. The authors have compiled a dataset of petroleum vapour and groundwater results from over 50 petroleum release sites in southern Africa. These data were used to develop exclusion distance criteria for vapours emitted from contaminated groundwater sources (i.e. distance from the source at which sufficient aerobic attenuation has occurred for the VI risk to be negligible). A standard "lines of evidence" approach has been applied to the assessment of VI risk by firstly applying the exclusion distance criteria to sites with groundwater contaminant plumes beneath buildings, and if these are met, the sites are considered to have no unacceptable VI risk. Where exclusion screening criteria are not met, risk is estimated using modelling, and if a potential risk is predicted, then direct sub-slab measurements are taken to more accurately assess the risk. Lastly, where sub-slab assessment predicts a potential VI risk, indoor vapour measurement are taken to evaluate actual risk, taking into account interferences from other sources and background levels of contaminants. Mitigating measures can then be applied as appropriate. Various case studies will be presented including direct measurements at industrial and residential sites overlying contaminant plumes and modelling methods at residential properties adjacent to service station sites. A risk-based approach to the assessment of contaminated land provides a sustainable and cost effective methodology, and also avoids unnecessary remediation. The results show that VI risks can be adequately addressed with a toolbox approach using multiple lines of evidence.

Abstract

The continuous increase in demand for water from a growing population and associated additional housing projects in the town of Steytlerville in the Eastern Cape Province has resulted in a shortage in water supply from the existing boreholes. In order to supplement the additional demand, a bulk water augmentation scheme using surface water from the Groot Rivier at a point immediately east of the Hadley crossing was implemented. This was done by drilling two large diameter production boreholes vertically into the alluvium and underlying bedrock of the river to a depth of intersecting the entire thickness of the mapped alluvium. Two boreholes were connected to a network of subsurface drains that allowed for recharge from the open channel to flow into the production boreholes. In addition to the sub-surface drain system connecting the sump boreholes, three recharge drains were constructed upstream of the abstraction boreholes. The purpose of these drains were to recharge the underlying paleo-channel to improve the water quality and yield from the paleo-channel. This was achieved by connecting the sub-surface drainage pipe to a vertical screened recharge borehole. The end result of the study was the successful implementation of a alternate borehole yield of 14l/s from the production wells to the Steytlerville town water reticulation supply.

Abstract

Data acquisition and Management (DAM) is a group of activities relating to the planning, development, implementation and administration of systems for the acquisition, storage, security, retrieval, dissemination, archiving and disposal of data. Data is the life blood of an organization and the Department of Water and Sanitation (DWS) is mandated by the National Water Act (No 36 of 1998) as well as the Water Services Act (No 108 of 1997), to provide useful water related information to decision makers in a timely and efficient manner. In 2009 the DWS National Water Monitoring Committee (NWMC) established the DAM as its subcommittee. The purpose was to ensure coordination and collaboration in the acquisition and management of water related data in support of water monitoring programs. The DAM subcommittee has relatively been inactive over the years and this has led to many unresolved data issues. The data extracted from the DWS Data Acquisition and Management Systems (DAMS) is usually not stored in the same formats. As a result, most of the data is fragmented, disintegrated and not easily accessible, making it inefficient for water managers to use the data to make water related decisions. The lack of standardization of data collection, storage, archiving and dissemination methods as well as insufficient collaboration with external institutions in terms of data sharing, negatively affects the management water resources. Therefore, there is an urgent need to establish and implement a DAM Strategy for the DWS and water sector, in order to maintain and improve data quality, accuracy, availability, accessibility and security. The proposed DAM Strategy is composed of the six main implementation phases, viz. (1) Identification of stakeholders and role players as well as their roles and responsibilities in the DWS DAM. (2) Definition of the role of DAM in the data and information management value chain for the DWS. (3) Development of a strategy for communication of data needs and issues. (4) Development of a DAM life Cycle (DAMLC). (5) Review of existing DAMS in the DWS. (6) Review of current data quality standards. The proposed DAM Strategy is currently being implemented on the DWS Groundwater DAM. The purpose of this paper is to share the interesting results obtained thus far, and to seek feedback from the water sector community.

Abstract

Water resource management and risk management rely heavily on the availability of data and information. This includes the volumes of water needed, the volumes of water available, where the available water is and where it would be needed, etc. Historical records help to determine past use and gives a way to predict future use in the case of water resource planning while it helps to predict the possibility of floods and droughts when it comes to risk management. Rainfall data can provide valuable data for both water resource planning and risk management, since it is the input to the hydrologicalcycle. It is possible to determine dry and wet cycles using the cumulative deviation from mean that is calculated from the measured rainfall data. This was done for the Gnangara Mound in Australia, with the results giving a fair representation of the dry and wet cycles in the area. Data measured over a period of about 30 years for the Zachariashoek sub-catchment analyzed in the same fashion provided wet-dry cycles of about 8 years. The rainfall measurements had been taken at various settings around the catchment, and varied from place to place and differed from that measured at the WeatherSA stations in the vicinity. This article will draw a comparison between the Zachariashoek data and the WeatherSA data to determine whether the WeatherSA data followed the same patterns for the wet-dry cycles observed in Zachriashoek. It will then analyse the longer data record available for the WeatherSA data from 1920 to 2012. It is expected that the shorter wet-dry cycles seen in Zachariashoek will become part of longer wet-dry cycles that can be used in water resource planning and risk management. Rainfall is also dependent on a number of factors

Abstract

Understanding the hydrogeochemical processes that govern groundwater quality is important for sustainable management of the water resource. A study with the objective of identifying the hydrogeochemical processes and their relation with existing quality of groundwater was carried processes in the shallow aquifer of the Lubumbashi river basin. The multivariate statistical approach includes self organizing maps (SOM'S) of neural networks, hierarchical cluster (HCA) and principal component analysis of the hydrochemical data were used to define the geochemical evaluation of aquifer system based on the ionic constituents, water types, hydrochemical facies and groundwater factors quality control. Water presents a spatial variability of chemical facies (HCO3- - Ca2+ - Mg2+, Cl- - Na+ + K+, Cl- - Ca2+ - Mg2+ , HCO3- - Na+ + K+ ) which is in relation to their interaction with the geological formation of the basin. The results suggests that different natural hydrogeochemical processes like simple dissolution, mixing, weathering of carbonate minerals and of silicate weathering and ion exchange are the key factors. Added to this is the imprint of anthropogenic input (use of fertilizers, septic practice poorly designed and uncontrolled urban discharges). Limited reverse ion exchange has been noticed at few locations of the study.

Abstract

Static indicator tests, such as acid-base accounting, are commonly used to provide an indication of ARD potential of backfill material in opencast coal mines. This potential for acidity is then commonly incorporated into numerical models, wrongfully, as a constant contamination source with the maximum possible sulphate being released from the pit, ad infinitum, which is, obviously, not the case. Dynamic tests on the other hand, are considered superior, but are expensive and time consuming. The proposed alternative approach is geochemical modelling, illustrated by a case study in the Mpumalanga coal fields. A decommissioned colliery near Carolina, Mpumalanga, was recently confronted with the prediction of the impacts that its backfilled opencasts might have on groundwater in the long term with regards to acid and contaminant generation, demanding a more realistic and well-defined conceptual and numerical approach than the simple minimum screening method. This study utilised the integration of a well-defined conceptual model, mineralogical data, acid-base accounting data, leaching test data, literature and groundwater monitoring data to address the long term hydrogeochemical evolution of groundwater at the colliery, using transiently calibrated geochemical and numerical flow models. Using the mineralogical data available from samples collected, as well as the sulphur content identified by ABA, a standard error was calculated for the abundances of all mineral phases present along with mean weight percentages, defining the likely boundaries of mineral abundances. Using these values along with reactive surface areas calculated from average grain sizes, using a collapsing core model, as well as rate constants from literature, the fluid rock interaction in the leaching tests was simulated and calibrated against leaching test results in the geochemical model, by varying mineral abundances, reactive surface areas and rate constants within the statistically acceptable boundaries. Once a calibrated mineral assemblage was identified using this method, the assemblage was geochemically modelled in the natural environment, after calculation of fluid to rock ratios, which in this case was purely potential backfill porosity vs. recharge due to the natural groundwater level being below the pit base, as well as potential oxygen fugacity. The calculated concentrations of constituents were then introduced into a transiently calibrated numerical flow and transport model via recharge concentrations, to also chemically calibrate this model. The chemical calibration was successful within a 20 mg/L range, illustrating the reliability of the conceptual and geochemical models, but also the reliability of predicted numerical modelling results. Based on the available data and modelling results, the colliery would not have a future impact on groundwater with regards to ARD and metals. However, elevated major cation and anion concentrations are expected, calculated within order of magnitude accuracy, and can be managed according to dynamic and realistic models, instead of a static worst case scenario.

Abstract

Mining is becoming a problem in the Western Cape - different kinds of mining and other resources, different problems than in other parts of the country. The West Coast had been declared a development corridor and a mining priority area. It is an arid to semi-arid area, where surface water is scarce, and rainfall relatively low and decreasing as one moves north. Some areas have significant volumes of good quality groundwater available, with potential impacts by the mining activities. This would play the importance of different resources off against the other. Most see resources as minerals, such as gold, silver, phosphate, and others where the value of these resources is measurable. Resources are also human capital, time, water, air, a healthy environment. It is more difficult to measure the value of the second group, as some of them have more than just a Rand and cent value. The value of resources is mostly done by measuring its monetary value, i.e. how much you will get when you sell the resource to a customer, providing the way the value of most resources is measured, i.e. resource economics. Economics is an area that most scientists are not familiar with as it contains a way thinking, of rules and laws unrelated to the way they have been taught. Supply and demand determines the value of a commodity, with scarce resources normally fetching higher prices. The value of the second group of resources is more difficult to determine. When does a resource become a strategic resource? This would be a resource that has a limited supply, does not get regenerated through natural processes and that is needed for defence, energy supply and others important for the stability of a country. There are also a category of resources we cannot live without such as water, and air - pure, fresh air and water. Without it life on this planet will cease to exist. This could be termed critical resources. What do you do if the occurrence of two very important critical resources overlaps, where the extraction of the one will lead to irreparable damage to the other? This article will look at one site where a strategic resource occurs at the same site as an important water resource. It will compare the potential value of the mineral resource with the value of the water resource in the aquifer measured at the current value of water as available to the public. It will also take into account the value of the water resource from the perspective of a healthy functioning ecosystem and a RAMSAR site. This analysis becomes more valuable when considering the potential effects of climate change in the area and the cost of desalination.

Abstract

A groundwater decision support system (DSS) that incorporates stakeholder participation has been developed for Siloam Village in Limpopo Province, South Africa. Residents of Siloam Village are dependent on groundwater to augment inadequate pipe borne water supply. This creates the need for a DSS that ensures efficient and sustainable management and utilization of water. Such a DSS is constituted of both quantitative and qualitative components. The study further proposes framework for implementation of the DSS which incorporates community participation. This will act as a tool for empowering and educating the communities in rural villages so that they can be able to manage their water resources. The developed DSSs will make it possible for Siloam community to operate their water supply systems efficiently taking into account environmental needs and water quality

Abstract

Slightly more out of the box idea is the use of anthropogenic aquifers as storage and chemical conditioners.  This concept was first introduce by Eland Platinum Mine(EPM) and reported on in previous papers.  At EPM water is used through a serious of natural aeration and aerobic storage facilities to reduce nitrate levels.  In 2013 another group introduced pilot studies by virtue of abstraction in support of the water conservation and demand management strategy; which has proven that it could enable the operations to overcome water shortage periods and reduce pressure on Rand Water (RW). The pilot sites would deliver water into the dirty water circuit, but within five to ten years it may further be used to overcome months with zero potable water supply. .  In platinum mines the more the aquifers are used the cleaner the water becomes, simply because introduced pollutants are not constant sources and country rock is mostly inert.  In the future these aquifers have the potential to become larger storage facilities protected from floods and limited evaporation losses. It is foreseen that some of the mines in the western belt may have more water stored in primary aquifers than water stored within major water dams. Yields from these aquifers for individual aquifers may be up to 450 m3/hour and storage of 18 Mm3.  . Why then this paper if we are already using it?  The issue is that the true value of these aquifers an only be unlocked when they are  used as recharging aquifers and thereby actively storing dirty water within a dirty water aquifer.  Once we are able to undertake this the positive environmental gains such of environmental overflows, condition dirty water, reduction of pollution and significant reduction of the use of potable water from RW. {List only- not presented}

Abstract

The International Association of Hydrogeologists and UNESCO's International Hydrological Programme have established the Internationally Shared (transboundary) Aquifer Resource Management (ISARM) Programme. This multiagency cooperative program has launched a number of global and regional initiatives designed to delineate and analyze transboundary aquifer systems and to encourage riparian states to work cooperatively toward mutually beneficial, sustainable aquifer development and management. The Stampriet Transboundary Aquifer System was selected as one of the three case studies funded by UNESCO. The Stampriet Aquifer System is located in the arid part of the countries (Botswana, Namibia and South Africa) where groundwater is a sole provider for water resource. The area is characterised by the Kalahari (local unconfined aquifer) and Nossob confined aquifer

Abstract

The Cedarville Flats aquifer located in the Upper Umzimvubu River Basin, Eastern Cape Province is a source of water supply for an important agricultural region in South Africa. The hydrogeology of this important aquifer is investigated to understand the occurrence, circulation, recharge and quality of groundwater. To this end, local and regional geology, borehole lithological logs, borehole yields, aquifer hydraulic characteristics (including aquifer thickness, water level, hydraulic conductivity, transmissivity and storage coefficient), hydrometeorological, hydrochemicaland environmental isotope data were collected and interpreted. The results show that the alluvial aquifer is made up of sand, gravel, boulders and clay and its thickness reaches 51 meters in places. Median hydraulic properties indicate that the Cedarville Flats primary aquifer is the most productive aquifer compared to the underlying Molteno and Burgersdorp Formations. It has an estimated median borehole yield in the order of 6 l/s as compared to 2 l/s for the Burgersdorp and 1.5 liters for the Molteno Formations. The aquifers in the area receive an estimated 7% of rainfall recharge. The groundwaters of the area are characterized by low ionic concentration with EC and TDS ranging from 235 to 285 ?S/cm and from 65 to 151 mg/l, respectively. The hydrochemical data further indicate a groundwater hydrochemical facies of either Ca-Na-Mg-HCO3 or Na-Ca-Mg-HCO3 highlighting a typically less evolved recharge area groundwater having short residence time and hence less water-rock interaction. Springs and artesian wells show a relatively depleted stable isotope and very low to dead tritium signals indicating high altitude recharge and longer circulation path and residence times compared to wells tapping the water table aquifer which indicate young water with recharge coming from the immediate surrounding area. Similarity in hydrochemical and stable isotope signatures between the streams that drain across the alluvial flats and the shallow groundwaters mean that there is a close interconnection between surface water and groundwater in the area.

Abstract

The Dahomey Basin is a transboundary sedimentary basin with its eastern half in south western Nigeria. The vulnerability assessment of the basin was carried out to ascertain the degree of the shallow unconfined aquifers sensitive to groundwater contamination through the investigations of the intrinsic properties of lithology over the unconfined aquifer systems. The basin is a multi-layered aquifer system hosting large population densities particularly in Lagos where nearly half of the population rely on the groundwater for domestics and industrial purposes. The vulnerability evaluation involves determining the protective cover and infiltration condition of the unsaturated zone in the basin. This was achieved using the PI vulnerability method of the European vulnerability approach. The PI method specifically measures the protection cover and the degree to which the protective cover is bypassed. Intrinsic parameters assessed were the subsoil, lithology, topsoil, recharge and fracturing for the protective cover. While, the saturated hydraulic conductivity of topsoil, infiltration processes and the lateral surface and subsurface flow were evaluated for the infiltration bypassed. The results were depicted in vulnerability maps. Map of the protective cover ranges from high to very high. This means a very effective cover over the groundwater resources. The I map revealed a low to very low degree of bypass. The final vulnerability map shows that the Dahomey Basin vulnerability ranges from moderate to very low vulnerability areas. Low vulnerability areas were characterised by lithology with massive sandstone and limestone, sub soils of sandy loam texture, high slopes and high depth to water table. The moderate vulnerability areas were characterised by high rainfall and high recharge, low water table, unconsolidated sandstones and alluvium lithology. The vulnerability map was validated with hydrochemical properties of the groundwater. Chloride and TDS concentration of the groundwater reveals high chloride concentration for low groundwater vulnerability areas while low chloride concentrations were observed for moderate vulnerability areas. Low to moderate groundwater vulnerability areas show low TDS concentrations according to the WHO standards except for the coastal areas with relatively higher TDS concentrations. The groundwater vulnerability maps will be a useful tool for planning land use activities which will minimise groundwater contamination and enhance the protection of the Dahomey Basin groundwater resources.
{List only- not presented}
Keywords: PI method, Dahomey Basin, aquifer vulnerability, protective cover, groundwater resources.

Abstract

When considering how to reduce contamination of petroleum hydrocarbons in shallow aquifers, it is important to recognize the considerable capacity of natural processes continuously at work within the secondary sources of contamination. This natural processes are technically referred to as Monitored Natural Attenuation (MNA), a process whereby petroleum hydrocarbons are deteriorated naturally by microbes. This approach of petroleum hydrocarbon degradation relies on microbes which utilise oxygen under aerobic processes and progressively utilises other constituents (sulphates, nitrates, iron and manganese) under anaerobic processes. MNA process is mostly evident when light non-aqueous phase liquids (LNAPLs) has been removed while the dissolved phase hydrocarbon compounds are prominent in the saturated zone. The case studies aim at determining feasibility and sustainability of Monitored Natural Attenuation process at different sites with varying geological setting.

Abstract

There is growing concern that South Africa's urban centres are becoming increasingly vulnerable to water scarcity due to stressed surface water resources, rapid urbanisation, climate change and increasing demand for water. Given South Africa's water scarcity, global trends for sustainable development, and awareness around the issues of environmental degradation and climate change, there is a need to consider alternative water management strategies. Water Sensitive Urban Design (WSUD) is an approach to sustainable urban water management that attempts to achieve the goal of a 'Water Sensitive City'. The concept of a Water Sensitive City seeks to ensure the sustainable management of water using a range of approaches such as the reuse of water (stormwater and wastewater), exploiting alternative available sources of supply, sustainable stormwater management and improving the resource value of urban water through aesthetic and recreational appeal. Therefore, WSUD attempts to assign a resource value to all forms of water in the urban context, viz. stormwater, wastewater, potable water and groundwater. However, groundwater is often the least considered because it is a hidden resource, often overlooked as a form a water supply (potable and non-potable) and it is often poorly protected. The management of urban groundwater and understanding the impacts of WSUD on groundwater in South African cities is challenging, due to complex geology, ambiguous groundwater regulations and management, data limitations, and lack of capacity. Thus, there is a need for an approach to assess the feasibility of management strategies such as WSUD, so that the potential opportunities and impacts can be quantified and used to inform the decision making process. An integrated modelling approach, incorporating both surface and subsurface hydrological processes, allows various urban water management strategies to be tested due to the complete representation of the hydrological cycle. This integration is important as WSUD is used to manage surface water, but WSUD known to utilise groundwater as a means of treatment and storage. This paper assesses the application, calibration and testing of the integrated model, MIKE SHE, and examines the complexities and value of establishing an integrated groundwater and surface water model for urban applications in South Africa. The paper serves to demonstrate the value of the application of MIKE SHE and integrated modelling for urban applications in a South African context and to test the models performance in Cape Town's unique conditions, accounting for a semi-arid climate, complex land use, variable topography and data limitations. Furthermore, this paper illustrates the value of integrated modelling as a management tool for assessing the implementation of WSUD strategies on the Cape Flats, helping identifying potential impacts of WSUD interventions on groundwater and the potential opportunities for groundwater to contribute towards ensuring to Cape Town's water security into the future.

Abstract

Aurecon was appointed to conduct groundwater exploration for production well fields in the towns of Setlagole and Madibogo. These towns are located in an arid part of the North West province on the edge of the Kalahari. The landscape is flat and covered by aeolian sand underlain by basement granite of the Kraaipan Group Geology.
Historically groundwater exploration consisted of reconnaissance geophysical surveys followed by detail ground surveys. Where no potentially water bearing geological structures are shown on geological maps & aerial photos, the project area would be divided into a grid on which the ground geophysical survey would be done. This type of exploration is time consuming and expensive. In some cases the terrain or cultural noise prohibits the use of conventional geophysical methods, with only more expensive and time consuming methods being left as an option. This is where the high resolution airborne magnetic survey excels. The results obtained from this type of survey are of such nature that only a small amount of ground geophysics is necessary to locate drilling targets. This survey method is also cost effective allowing a larger area to be covered in a short amount of time as compared to conventional ground techniques.
This paper will discuss successes achieved using high resolution aeromagnetic surveys as the basis for groundwater exploration in traditionally low-yielding igneous geology.

Abstract

Preventing the spread of seepage from tailings storage facilities (TSF's) in groundwater is necessary as it often contains toxic contaminants. Experience has shown that seepage from TSFs is inevitable and that zero seepage remains difficult even with complex liner systems. Multiple seepage control methods are often required to minimise seepage to ensure that environmental regulations are met. Control methods can be grouped into either barrier or collection systems. Barrier systems are used to hinder seepage whereas collection systems are used to intercept seepage. A blast curtain, which is the focus of this article, is a type of collection system that is still at a conceptual level but has seen little or no application worldwide. It works in principle, similarly to a curtain drain, but is typically extended to greater depths depending on the aquifer vulnerability. Numerical modeling has shown that this mitigation measure could add another line of defence for seepage control. The depth and effectiveness of the curtain can be optimized with a numerical model to ensure optimal interception of contaminated seepage around the TSF. Depths of up to 30 m in fractured aquifers have been simulated in this study. A blast curtain is constructed by drilling a set of boreholes around a TSF in close proximity to one another and then fracturing the rock using either explosives or fracking methods to create a more permeable zone. This is then combined with a series of scavenger wells or natural seepage to abstract the contaminated water. Numerical simulation has shown that blast curtains are effective especially if groundwater flow is horizontal. The effectiveness decreases if the vertical flow component is significant. A blast curtain can result in the lowering of the water table, however, local depression is a less of a concern than potential groundwater contamination. {List only- not presented}

Abstract

POSTER Most developing urban areas in semi-arid regions of Sub Saharan Africa are often forced to utilise groundwater as an alternate source of domestic water supplies. As such groundwater evaluations strategies often face dual challenges in terms of resource quantification and their quality evaluation. However, groundwater potential assessment and aquifer yield evaluations often present a challenge when the system is of crystalline basement nature where groundwater potential is highly spatially variable and cases of dry holes and seasonal wells have been reported. This study demonstrate the integrated combination of geophysical techniques, (namely, vertical electrical sounding, electrical resistivity tomography, magnetic mapping, and seismic refraction tomography) with both borehole monitoring and infiltration techniques in the groundwater prospecting and spatial yield analysis of the Urban Bulawayo crystalline basement aquifer. The Bulawayo Metropolitan Province of Zimbabwe is located in the semi-arid region of Zimbabwe with an average annual rainfall of below 500 mm and has had a prolonged dry spell has resulted in the dwindling of the existing surface water resources. The aquifer system consists of syenite granite and fractured basaltic greenstone crystalline basement complexes. Provisional geophysical results have shown that the thickness of the fractured zone sharply varies in terms of spatial distribution and often some sections are characterized by shallow surface fractured zone that may only be 20-30 m thick and some sections have a reported regolith of up to 60m in thickness. Borehole yield assessments and chemical analysis techniques will be done on drilled wells in order to come out with detailed spatial variation in the borehole yield and water quality variations across the aquifer system. All the technical evaluations are then integrated to produce a detailed hydro-geophysical map of the system that can be used in the technical groundwater management of the urban Bulawayo aquifer.

Abstract

POSTER As the National Water Act has evolved to provide for more effective and sustainable management of our water resources, there has been a shift in focus to more strategic management practices. With this shift come new difficulties relating to the presentation of sensitivity issues within a spatial context. To this end it is necessary to integrate existing significant spatial layers into one map that retains the context, enables simple interpretation and interrogation and facilitates decision making. This project shows the steps taken to map and identify key groundwater characteristics in the Karoo using Geographic Information Systems (GIS) techniques. Two types of GIS-based groundwater maps have been produced to assist with interpretation of existing data on Karoo Aquifer Systems in turn informing the management of groundwater risks within Shell's applications for shale gas exploration. Aquifer Attribute and Vulnerability maps were produced to assist in the decision making process. The former is an aquifer classification methodology developed by the project team, while the latter uses the well-known DRASTIC methodology. The overlay analysis tool of ESRI's ArcGIS 10.1 software was used, enabling the assessment and spatial integration of extensive volumes of data, without losing the original detail, and combining them into a single output. This process allows for optimal site selection of suitable exploration target areas. Weightings were applied to differentiate the relative importance of the input criteria. For the Attributes maps ten key attributes were agreed by the project team to be the most significant in contributing to groundwater/aquifer characteristics in the Karoo. This work culminated in the production of a series of GIS-based groundwater attributes maps to form the Karoo Groundwater Atlas which can be used to guide groundwater risk management for a number of purposes. The DRASTIC model uses seven key hydrogeological parameters to characterise the hydrogeological setting and evaluate aquifer vulnerability, defined as the tendency or likelihood for general contaminants to reach the watertable after introduction at ground surface.

Abstract

Groundwater provides an important buffer to climate variability in Africa. Yet, groundwater irrigation contributes only a relatively small share of cultivated land, approximately 1% (about 2 mill. ha) as compared to 14% in Asia. While groundwater is over-exploited for irrigation in many parts in Asia, previous assessments indicate an underutilized potential in parts of Africa. As opposed to previous country-based estimates, this paper derives a continent-wide, distributed (0.5 degrees spatial resolution) map of groundwater irrigation potential, indicated in terms of fractions of cropland potentially irrigable with renewable groundwater. The method builds on an annual groundwater balance approach using 41 years of hydrological data, allocating only that fraction of groundwater recharge that is in excess after satisfying other present human needs and environmental requirements, while disregarding socio-economic and physical constraints in access to the resource. Due to high uncertainty of groundwater environmental needs, three scenarios, leaving 30, 50 and 70% of recharge for the environment, were implemented. Current dominating crops and cropping rotations and associated irrigation requirements in a zonal approach were applied in order to convert recharge excess to potential irrigated cropland. Results show an inhomogeneously distributed groundwater irrigation potential across the continent, even within individual countries, mainly reflecting recharge patterns and presence or absence of cultivated cropland. Results further show that average annual renewable groundwater availability for irrigation ranges from 692 to 1644 km3 depending on scenario. The total area of cropland irrigable with renewable groundwater ranges from 44.6 to 105.3 mill. ha, corresponding to 20.5 to 48.6% of the cropland over the continent. In particular, significant potential exists in the semiarid Sahel and eastern African regions which could support poverty alleviation if developed sustainably and equitably. The map is a first assessment that needs to be complimented with assessment of other factors, e.g. hydrogeological conditions, groundwater accessibility, soils, and socio-economic factors as well as more local assessments.

Abstract

Introduction: Verlorenvlei catchment in the renowned potato Sandveld area is shared by three main towns where agriculture is a primary economic activity. This semi-arid catchment, receives low winter rainfall, but has a dynamic groundwater system providing almost all water services in the catchment and sustaining the acclaimed Verlorenvlei RAMSAR site. There have been recurring concerns of land use as a potential threat to water resources and the sustainability of Verlorenvlei RAMSAR site. The Minister of Water and Sanitation as custodian of water resources requires that surface water use less than 18 250 m3 and ground water use less than 3 650 m3/a to be granted under general authorization. All water use above such general authorization volumes is to be registered (Government Gazette No. 20526 of 1999). Water use registration, is identified as a tool used to achieve the effective management and governance of water resources. Water use above general authorization, is associated with larger scale land use activity, which may have an impact on water resources and the environmental at large. The following study, seeks to examine and compare catchment water use for land uses, to catchment water availability using water use registration data. Comparing water allocation and catchment capacity, this study further seeks to explore the effectiveness of water use registration in achieving good governance of water resources. Purpose: The purpose of this study was to determine effectiveness of water use registration in promoting good governance in the Verlorenvlei catchment Results: Of 124 registered water users identified in the Verlorenvlei catchment, only two of these water users are within the legislative limit outlined by Government Gazette No. 20526 of 1999. Overall, permissible water use is 447 547 259.5 m3/a, over 10 times the catchment capacity of 40 000 000 m3/a. Conclusion: Overall, excessive water use for land use activity is observed within the catchment, despite provision of legislature guiding against excessive water use. Increased water use registration, does however correlate with improved land use practices for agricultural production (Potato SA, 2014) suggesting probability of good governance. Lastly, there is a need for monitoring; improved water and land use efficiency, Integrated Water Resources Management and good governance in the catchment.

Abstract

2-D Electrical Resistivity Tomography (ERT) and hydrochemical study have been conducted at El Sadat industrial city. The study aims at investigating the area around the waste water ponds to determine the possibility of water percolation from the wastewater (oxidation) ponds to the Pleistocene aquifer and to inspect the effect of this seepage on the groundwater chemistry. Pleistocene aquifer is the main groundwater reservoir in this area, where El Sadat city and its vicinities depend totally on this aquifer for water supplies needed for drinking, agricultural and industrial activities. In this concern, 7 ERT profiles were measured around the wastewater ponds.

Besides, 10 water samples were collected from the ponds and the nearby groundwater wells. The water samples have been chemically analyzed for major cations (Ca+2, Na+, K+, Mg+2), major anions (Cl-, CO3-2, HCO3-, SO4-2), nutrients (NO2-, NO3-, PO4-3) and heavy elements (Cd, V, Cr, Zn, Ni, Cu, Fe, Mn, Pb). Also, the physical parameters (pH, Alkalinity, EC, TDS) of the water samples were measured. Inspection of the ERT sections shows that they exhibit lower resistivity values towards the water ponds and higher values in opposite sides. Also, the water table was detected at shallower depths at the same sides of lower resistivity. This could indicate a wastewater infiltration to the groundwater aquifer near the oxidation ponds. Correlation of the physical parameters and ionic concentrations of the wastewater (ponds) samples with those of the groundwater samples indicates that; the ionic levels are randomly varying and no specific trend could be obtained. Also, the wastewater samples shows some ionic levels lower than those detected in other groundwater samples. Besides, the nitrate level is higher in samples taken from the cultivated land than the wastewater samples due to the over using of nitrogen fertilizers. Then, we can say that the infiltrated water from wastewater ponds are NOT the main controller of the groundwater chemistry in this area, but rather the variable ionic concentrations could be attributed to local, natural and anthropogenic processes.

Abstract

Multi-data integration approach was used to assess groundwater potential in an area consisting crystalline basement and carbonate rocks that are located in the North West Province of South Africa. The main objective of the study is to evaluate the groundwater resource potential of the region based on a thorough analysis of existing data combined with field observation. Integration of six thematic layers was supplemented by a statistical analysis of the relationship between lineaments density and borehole yield. Prior to data integration, weighting coefficients were computed using principal component analysis.
The resulting thematic layer derived from integration of the six layers revealed a number of groundwater potential zones. The most probable groundwater potential zones cover ~14% of the entire study area and located within carbonate rocks consisting limestone and dolomite. The presence of pre-existing structures together with younger and coarse sedimentary rocks deposited atop the carbonate rocks played a significant role in the development of high well fields in the southern part of the area. Moderate-to-high groundwater potential zones within Ventersdorp lava coincide with maximum concentrations of fractures. The results of statistical correlation suggest that 62% of high borehole yield within the Ventersdorp lave can be attributed to fracture density. In general, the present approach is very effective in delineating potential targets and can be used as a sound scientific basis for further detailed groundwater investigation.
KEY WORDS:- Multi-data, thematic layers, groundwater, carbonate rocks, structures

Abstract

The Department of Water Affairs and Sanitation is the custodian of the Water Resource in South Africa. The Western Cape Regional Office, Geotechnical Service Sub Directorate, is responsible for management of groundwater resources in two Water Management Areas (WMA), Olifants Doorn-Berg and Breede-Gouritz. Twenty-nine monitoring routes comprising 800 sites in total are monitored across the Western Cape Region. The purpose of this paper is to create awareness of groundwater related databases and the type of information products used in assessing the status of data bases and groundwater resources. This is to assist and support the scientists, technicians, managers, external stakeholders and/or general public. The main question that needs to be answer is: "What is the current groundwater data management situation in the Regional office?" With the GIS as platform, geographical information was generated from existing data bases to answer questions such as, what is being monitored, where is it being monitored, who is monitoring it, why is it being monitored and when is it being monitored? These questions are applicable to the Region, Water Management Areas, the monitoring route and geosites. Graphical time-series information generated from available data, in combination with the generated geographical information, showed the gaps, hot spots and what is still needed for all the facets of groundwater management (from data acquisition to information dissemination) processes. The result showed the status of data bases, need for data in areas of possible neglect, training gaps, inadequate structure and capacity, instrumentation challenges, need for improvement of commitment and discipline, as well as many other issues. The information generated proves to be an easy tool for Scientists, Technicians and Data Administrators to assist them to be on top of the groundwater resource management in their area of responsibility. The expansion of the use of GIS as a groundwater management tool is highly recommended. This will ensure better understanding of the resource: "The Hidden Treasure".

Abstract

An understanding of the movement of moisture fluxes in the unsaturated zone of waste disposal sites play a critical role in terms of potential groundwater contamination. Increasing attention is being given to the unsaturated or vadose zone where much of the subsurface contamination originates, passes through, or can be eliminated before it contaminates surface and subsurface water resources. As the transport of contaminants is closely linked with the water ?ux in through the unsaturated zone, any quantitative analysis of contaminant transport must ?rst evaluate water ?uxes into and through the this region. Mathematical models have often been used as critical tools for the optimal quantification of site-speci?c subsurface water ?ow and solute transport processes so as to enable the implementation of management practices that minimize both surface and groundwater pollution. For instance, numerical models have been used in the simulation of water and solute movement in the subsurface for a variety of applications, including the characterization of unsaturated zone solute transport in waste disposal sites and landfills. In this study, HYDRUS 2D numerical simulation was used to simulate water and salt movement in the unsaturated zone at a dry coal ash disposal site in Mpumalanga, South Africa. The main objective of this work was to determine the flux dynamics within the unsaturated zone of the coal ash medium, so as to develop a conceptual model that explains solute transport through the unsaturated zone of the coal ash medium for a period of approximately 10 year intervals. Field experiments were carried out to determine the model input parameters and the initial conditions, through the determination of average moisture content, average bulk density and the saturated hydraulic conductivity of the medium. A two dimensional finite-element mesh of 100m x 45m model was used to represent cross section of the ash dump. Two dimensional time lapse models showing the migration of moisture fluxes and salt plumes were produced for the coal ash medium. An explanation on the variation of moisture content and cumulative fluxes in the ash dump was done with reference to preexisting ash dump data as well as the soil physical characteristics of the ash medium.
{List only- not presented}

Abstract

Shale gas in South Africa can be a game changer for the Karoo and South Africa economy but it may have a devastating effect on the environment. The Karoo communities is highly reliable on groundwater for their stock, irrigation and also for domestic use. Knowing the process and the potential impacts of gas-well drilling and fracturing on shallow groundwater systems beforehand different appropriate studies can be done before any hydraulic fracturing can took place in South Africa. The biggest concerns with hydraulic fracturing is that the fracturing fluids will flow and discharge into shallow aquifers due to the high pressure used or the produced water mixed with deep saline water may discharge into the environment. This paper presents a baseline dataset that will be a reference point against which any future changes in groundwater concentrations can be measured. The Karoo basin with its numerous dolerite intrusions make it unique and different from other countries. These dolerite intrusions are associated with high yielding boreholes because of the fractured contact. The Karoo Basin may be under artesian conditions, which imply that any pollutant might migrate upwards in the Karoo. The understanding of key attributes for characterising groundwater of Karoo Aquifers is most importantly the depth to water level, the yield, and groundwater quality.. The understanding of these characteristics will help to close possible legislative loopholes regarding fracturing. This paper establish an interactive database to obtain full understanding of the hydrogeology of the Karoo to be able to quantify how much water is available in the Karoo and who is the users. Not only the quantity of the water in the Karoo, but also quality and age/origin by making use of different isotopes in conjunction with basic macro chemistry. This will allow for a broader picture before any unconventional gas mining in the Karoo takes place and it can be used to identify any future changes in groundwater quality and quantity of the Karoo aquifers.

Abstract

Groundwater in South Africa is the most important source of potable water for rural communities, farms and towns. Supplying sufficient water to communities in South Africa becomes a difficult task. This is especially true in the semi-arid and arid central regions of South Africa where surface water resources are limited or absent and the communities are only depended on groundwater resources. Due to a growing population, surface water resources are almost entirely being exploited to their limits. These factors, therefore, increases the demand for groundwater resources and a more efficient management plan for water usage. For these reasons, the relation between the geology and geohydrology of South Africa becomes an important tool in locating groundwater resources that can provide sustainable quantities of water for South Africans. It was therefore decided to compile a document that provides valuable geohydrological information on the geological formations of the whole of South Africa. The information was gathered by means of interviews with experienced South African geohydrologists and reviewing of reports and articles of geohydrological studies. After gathering the relevant information, each major geological unit of South Africa together with its geohydrological characteristics was discussed separately. These characteristics include rock/aquifer parameters and behaviour, aquifer types (primary of secondary), groundwater quality, borehole yields and expected striking depths, and geological target features and the geophysical method used to locate these targets. Due to the fact that 90 % of South Africa's aquifers are classified as secondary aquifer systems, groundwater occurrence within the rocks of South Africa is mainly controlled by secondary fractures systems; therefore, understanding the geology and geological processes (faulting, folding, intrusive dyke/sills & weathering) responsible for their development and how they relate is important. However, the primary aquifers of South Africa (Coastal Cenozoic Deposits) should not be neglected as these aquifers can produce significant amounts of groundwater, such as the aquifer units of the Sandveld Group, Western Cape Province. Drilling success rates and possibility of striking higher yielding boreholes can be improved dramatically when an evaluation of the structural geology and geohydrological conditions of an area together with a suitable geophysical method is applied. The ability to locate groundwater has been originally considered (even today) a heavenly gift and can be dated back to the Biblical story of Moses striking the rock to get water: "behold, I will stand there before thee there upon the rocks thou shalt smite the rock and there shall come water out of it" (Exodus 17:6).

Abstract

Studies have shown that the use of natural water (drinking and bathing) with high level of 222Rn concentration may contribute to negative health effect in human beings. Thermal springs located in Limpopo province were sampled for the determination of 222Rn concentration by gamma ray spectrometry. The spring water has been used for domestic purposes: drinking and bathing, and for recreation bathing mainly. 19 samples were collected between thermal springs emanation points and swimming facilities (out and in doors). Radon-222 concentration found in these water ranges from 0.2 to 624 Bq/l. These results indicate that 7 thermal springs may represent increasing risk on bathing or inhalation of radon gas, leading to an increased risk of healthy.

Abstract

Coal constitutes 77% of the primary energy needs in the country, with the Waterberg Coalfield estimated to host about 40% of the remaining South African coal resources. The Karoo coals were deposited in a reduced environment that have the potential to produce sulphides within the sediments they are hosted. The sulphur content within the coal can range from 0.1 wt.% to as high as 10 wt.%. Mining generates a disturbance in the natural groundwater levels and affects the surrounding water chemistry when sulphate is produced as a result of pyrite oxidation. Acid base accounting (ABA) was used to determine the balance between the acid producing potential (AP) and acid neutralizing potential (NP). From the analysis the Net Neutralising Potential (NNP) classified samples as either acid or non-acid producing. ARD does not only result in the generation of acid but is accompanied by decreased pH and increased values of specific conductance, dissolved metals and sulphate. The ABA results showed that interburden and coal samples have higher risks of producing acid upon oxidation than overburden samples. Higher concentrations of neutralising minerals are present in overburden samples. ABA indicated that the material 60m below ground surface had a higher acid producing potential than the material above. The analysis from kinetic tests showed the long-term behaviour of different samples, with the electrical conductivity (EC) and pH changing over time. Samples with lower pH continued to produce more sulphate, while calcium continued to increase until it was depleted from the samples. Inductively coupled plasma analysis determined the release of the heavy metals which can be detrimental to the environment, such as As, Co, Ni and Pb. The water demand will increase as mining continues in the area, with inter-catchment transfers identified to overcome local water scarcity issues. ARD poses a big threat to both groundwater and surface water resources.

Abstract

Environmental isotope techniques have been successfully applied in the field of hydrogeology over the last couple of decades and have proved useful for understanding groundwater systems. This paper describes a study of the environmental isotopes for Oxygen (18O) and Hydrogen (1H, 2H-Deutrium, 3H-Tritium) obtained from various points in and around the underground coal gasification (UCG) site in Majuba, South Africa. UCG is an alternative mining method, targeting deep coal seams that are regarded as uneconomical to mine. The process extracts the energy by gasifying the coal in-situ to produce a synthetic gas that can be used for various applications. The site consists of shallow, intermediate and deep aquifer systems at a depth of 70m, 180 and 300m respectively. The intermediate aquifer is further divided into the upper and lower aquifer systems.
Samples were taken from each aquifer system together with supplementary samples from the Witbankspruit and an on-site water storage dam. A total of 15 samples were submitted for isotope analyses. By investigating the various isotopic signatures from all the samples taken, it will be possible to determine if there are similar or contrasting isotopic compositions by deducing possible water source for each sample due to isotopic fractionation caused by physical, chemical and biological processes. This will also be supported by deducing the mean residence time (MRT) for each water source sampled based on the Tritium data as well as the chemistry data already available for different sources. The chemistry data established linkages between the upper and lower intermediate aquifers.{List only- not presented}
Key words: Environmental isotopes, UCG, Water source, Isotope fractionation

Abstract

The understanding of groundwater and surface water interaction is important for the planning of water resources in particular for farming areas. The interactions between groundwater and surface water are complex. To understand the relationship of groundwater and surface water interactions it is important to have a good understanding of the relation of climate, landform, geology, and biotic factors, a sound hydrogeoecological framework. Surface-water and groundwater ecosystems are viewed as linked components of a hydrologic continuum leading to related sustainability issues. In this study the Gevonden farm in Rawsonville will be used as the study site. This study site forms part of the Table Mountain Group (TMG). The methods to establish the relationship of groundwater and surface water interaction are collection of rainfall data monthly, river channel parameters at the farm such as the discharge on a monthly bases, chemistry of the water in the stream and groundwater were also be analyzed and pumping tests will be conducted twice to get the hydraulic parameters of the aquifer. The aquifer parameters will be analyzed using the Theis and Cooper-Jacob methods. The river has lower water levels in the summer months and this is also the case in the water levels in the boreholes on the farm, however in winter the opposite is true. The chemical analyses which are identical indicate that there is groundwater and surface water interaction in the farm. The degree of the interaction differs throughout the year. The results show that the interaction is influenced by the rainfall. The results clearly suggests that the farmers need to construct dams and drill pumping borehole in order to have enough water to water their crops in the summer season as by that time the river is almost dry.
{List only- not presented}

Abstract

The Bedford Dam is the upper storage dam for the Ingula Pumped Storage Scheme and is situated in the Ingula/Bedford Wetland. This wetland has a high structural diversity which supports a unique assemblage of plants and invertebrates. The flow regulation and water purification value is of particular importance as the wetland falls within the Greater Vaal River catchment. Concern was raised with respect to the potential negative impact of the newly constructed dam on the dynamic water balance within the wetland. An assessment of the extent to which groundwater drives / sustains the wetland systems and the water requirements needed to sustain the wetland processes was determined. This includes establishing the impact of the Bedford Dam on the groundwater and wetland systems as well as providing recommendations on management and monitoring requirements. The hydropedological interpretations of the soils within the study area indicate that baseflow to the wetland is maintained through perennial groundwater, mainly recharged from infiltration on the plateau, and was confirmed through isotope sampling and hydrometric measurements. It is apparent that the surface flows in the main wetland are fed by recent sources, while the subsurface layers in the wetland are sustained by the slower moving near-surface and bedrock groundwater. The movement of groundwater towards the wetland is hindered by the numerous dykes creating a barrier to flow. Nevertheless, there seems to be a good connection between the groundwater sources in the upland and the surface drainage features that conduct this water to the contributing hillslopes adjacent to the main wetland. The surface flows of the main wetland are sustained by contributions from tributary fingers. The discharge out of the wetland is highly seasonal

Abstract

Two ventilation shafts were proposed to be excavated to depths of 100 and 350 m to intersect an underground mine, in the Bushveld Complex. The area is made up of fractured aquifers and the assignment was to identify the exact positions of the permeable zones within the shafts profiles as well as estimate the groundwater inflow rates at every 5 m interval along the shafts profiles. The project was budget and time constrained and therefore the preferred hydrogeological characterisation techniques, particularly the percussion drilling, aquifer testing and numerical modelling could not be conducted. The study was completed by conducting packer tests in HQ sized holes drilled at the exact positions of the proposed shafts. The packer test data was then interpreted using Thiem equation, a modification of Darcy Equation for radial flow, to estimate the steady state inflow rates into the shafts. Transient state flow is more challenging to calculate analytically, as it is time and aquifer storage dependent. However, transient state flow in shafts exists for the first 10 - 15 days only and is short lived. Thereafter, a steady state flow occurs where the rate is nearly fixed for the rest of the life of mine, unless new external stresses, such as mine dewatering, takes place within the radius of influence. Six months later the shafts were excavated and the permeable zones were encountered at the exact positions as predicted using the packer testing. In addition, the inflow rates calculated using analytical modelling was successful in estimating the inflow rates recorded after the shafts were excavated. The packer testing and analytical modelling was therefore effective in assisting the mine to plan the necessary pumps and management plans within the allocated budget and timeframe.

Abstract

Define chemical signatures from river waters collected in the Crocodile (West) and Marico Water Management Areas, South Africa. Samples were analysed for anion complexes using Ion Chromatography (IC) and major and trace element chemistry using quadrupole Inductively Coupled Plasma-Mass Spectrometry (q-ICP-MS). Results are used to define the various chemical signatures resulting from activities within the study area which include mining, agriculture, industry, residential and domestic, and recreational usage and to differentiate the 'background' that arises from the natural geological heterogeneity. The aim of this characterisation is to fingerprint the chemical signatures of various anthropogenic activities irrespective of background. Results from this investigation have been mapped using GIS to visualise the data across the study area. Based on the results, the contamination sources within the area can be identified and ranked in terms of their contribution to the total effective contamination received at Hartebeespoort Dam. {List only- not presented}

Abstract

The Oudtshoorn Groundwater Project aims to target deep groundwater as a long-term option to augment the water supply to the greater Oudtshoorn Local Municipality. Located 15 km south of Oudtshoorn towards the Outeniqua Mountain range, the Blossoms Wellfield lies within a potentially high-yielding artesian basin. The Peninsula Formation (of the Table Mountain Group (TMG), hydrostratigraphically known as the Peninsula Aquifer, is exposed in the Outeniqua Mountains (high rainfall recharge area), and is deeply confined northwards by the overlying Bokkeveld Group.
The project is currently emerging from an exploration phase, with eight existing boreholes that target the deep confined Peninsula Aquifer, and three boreholes that monitor the shallower Nardouw (Skurweberg) Aquifer. Estimation of the aquifer's productive and sustainable groundwater potential involves determining its hydraulic properties by stressing the aquifer through flow and pumping tests and accurately monitoring flow rates, the potentiometric surface level (PSL) during flow, and PSL recovery thereafter. Free-flow and pumping tests were carried out on four boreholes between the 12th May 2014 and the 29th June 2014. The boreholes were all equipped with data-loggers to record pressure and flow-meters to determine the flow-rate. Recovery of the aquifer after the testing is still being continuously monitored.
Results from the month and a half flow-test show that there is no interaction between the deep confined Peninsula Aquifer and the shallower Nardouw Aquifer beneath the southern part of the wellfield. Because the water-use licence stipulates that there can be no negative impact from Peninsula Aquifer abstraction on the Nardouw Aquifer, which is utilised by farmers in the region, this issue is of paramount importance. The hydrochemical signature of the two aquifers is also different.
Recovery monitoring emphasised that the northern block is better inter-connected through fracture systems than the southern block, because those boreholes recovered to their original potentiometric surface almost immediately, whereas the southern boreholes took days for recovery. Two boreholes in the south are still recovering eight months later, which is most likely due to their being drilled into the limb of folded rock systems and not the more fractured hinge zone (as with the more connected boreholes).
Using the drawdown and recovery curves ('Horner plots'), the transmissivity and storativity of the aquifer is calculated analytically by the Theis equation. The results show a large variation in storativity (1.0E-1 to 1.46E-4) and transmissivity (9-20 m2/day) between the various boreholes, emphasising the heterogeneity of the aquifer. The aquifer properties gained from this testing are essential in better understanding the aquifer system, and developing numerical models for future wellfield testing and model simulation.

Abstract

The management of groundwater inflows into an opencast colliery in Mpumalanga is normally fairly easily achievable due to low inflow volumes and high evaporation rates. But, when flooded underground mine workings are encountered, groundwater inflow complexity increases dramatically. Understanding, predicting and managing groundwater inflow under these conditions can be challenging and highly complex. While normal opencast inflows are easily modelled these connected mines are pushing numerical models to their limits. This case study aims to illustrate an approach based on a finite difference model that has been used successfully in a South African coal mine. Based on a study at a colliery near Ermelo, Mpumalanga, the understanding and conceptualisation of the aquifer geometry, geological structures, hydrogeology, defunct underground mine geometry and interconnection between opencasts and the underground, proved to be vital, not only in calibration of the model, but also in the construction of the various layers and calculation of flow volumes between the various sources and sinks. This also aided greatly in constant source contaminant transport modelling to trace which mining areas may have a contamination effect on each other or the surrounding aquifer. In constructing the numerical flow model, the underground mine geometry was found to intersect various layers in the MODFLOW based model and pinching out in some areas. Due to the requirement of MODFLOW that layers should be continuous with no pinchouts to the model boundaries, this presented a notable challenge in the model construction. Therefore, mine geometry was divided into various slices, fitting within the hydrogeological layers, but still retaining the original geometry. The layers were then further divided laterally using different materials to represent the mine hydraulic properties and aquifer properties respectively, ensuring that the lateral distribution of materials also represents the underground mine geometry accurately. Using this model construction, the calculated mean residual head for the simulation of the current situation was found to be less than 3m while the simulation of the current mining situation with no underground mine present, yielded a mean residual head of approximately 10m. Additionally, inflows measured in the opencast penetrating the underground were measured at approximately 1000m3/d while the calibrated model calculated inflows of 1160m3/d, while simulating the current mining situation including the defunct underground. The current decant from the defunct underground, to the southeast of the site, was calculated as 1.9 L/s by the model while the measured rate was just over 1 L/s. Also, as expected, the dewatering of the opencast penetrating the flooded, defunct underground mine, was calculated to predominantly impact an underground mine compartment, isolated by underground seals, as opposed to the aquifer, which has a much lower hydraulic conductivity. {List only- not presented}

Abstract

South Africa is a country at the forefront of the solar energy revolution. Each solar energy plant implementation results in further supply of clean renewable energy to the South African electric grid, thus playing a part in helping South Africa meet its renewable energy targets, in addition to stimulating long-term economic development and creating new jobs. Active solar techniques include the use of photovoltaic systems, concentrated solar power and solar water heating to harness the energy. Particular focus has recently been on the use of concentrated solar power technology which is better able to address the issues of scalability and electric storage. The process includes the use of a liquid salt solution and also requires a reliable water source. When applying for a new solar energy plant, a geohydrological assessment is required to inform the Environmental Impact Assessment. SolarReserve South Africa (Pty) Ltd responsibly take this one step further by requesting detailed geohydrological assessments including drilling and field testing, numerical modelling and simulations, and detailed impact analysis. Of particular consideration in these assessments is the potential for groundwater to meet the plants water needs, as well as the assessment of risk and potential groundwater contamination impact from failure in the lining of the evaporation ponds. This paper describes the 'best practice' approach that has been formulated and undertaken for some previously proposed sites, and is now recommended for future use in the groundwater impact assessment of future proposed solar energy plants in South Africa. It makes use of a SolarReserve case study example, located at the farm Kalkaar near Jacobsdal in the Free State Province, to explain the main steps in the process and how the results of using this approach are important inputs in the assessment of impacts, decision-making regarding go/no-go, technology used, infrastructure and site layout, and responsible management and monitoring of the groundwater in the future.

Abstract

Globally, a growing concern have been that the heavy metal contents of soil are increasing as the result of industrial, mining, agricultural and domestic activities. While certain heavy metals are essential for plant growth as micronutrients, it may become toxic at higher concentrations. Additionally, as the toxic metals load of the soil increases, the risk of non-localized pollution due to the metals leaching into groundwater increases. The total soil metal content alone is not a good measure of risk, and thus not a very useful tool to determine potential risks to soil and water contamination. The tendency of a contaminant to seep into the groundwater is determined by its solubility and by the ratio between the concentration of the contaminant sorbed by the soil and the concentration remaining in solution. This ratio is commonly known as the soil partitioning or distribution coefficient (Kd). A higher Kd value indicate stronger attraction to the soil solids and lower susceptibility to leaching. Studies indicate that the Kd for a given constituent may vary widely depending on the nature of the soil in which the constituent occurs. The Kd of a soil represents the net effect of several soil sorption processes acting upon the contaminant under a certain set of conditions. Soil properties such as the pH, clay content, organic carbon content and the amount of Mn and Fe oxides, have an immense influence on the Kd value of a soil. Kds for Cu, Pb and V for various typical South African soil horizons were calculated from sorption graphs. In most cases there were contrasting Kd values especially when the cations, Cu and Pb, had high contamination levels, the value for V was low. There is large variation between the Kds stipulated in the Framework for the Management of Contaminated land (as drafted by the Department of Environmental Affairs) and the values obtained experimentally in this study. The results further indicate that a single Kd for an element/metal cannot be used for all soil types/horizons due to the effect of soil properties on the Kd. The results for Cu and Pb indicated that the Kds can range in the order of 10 to 10 000 L/kg for Cu and 10 to 100 000 L/kg for Pb. The variation in V Kd was not as extensive ranging from approximately 10 to 1 000 L/kg. {List only- not presented}

Abstract

The proposed underground copper mine is one of the first Greenfield developments in the Kalahari Copper Belt. Groundwater resources in the region are scare and saline mainly due to minimal recharge. Management and simulations of groundwater inflows formed an integral part of the new mine design to reduce production losses caused by the inflows and to ensure a safe mining environment. The mine is located is a complex hydrogeological setting characterised by folding and deep water levels. Multiple fractured aquifers are associated with the mining area. Groundwater numerical modelling was performed in Groundwater Modelling System (GMS) using MODFLOW-NWT. Results of the scenarios were used as a management tool to aid in the potential inflow predictive simulations and dewatering management. The numerical model was calibrated by using field measured aquifer parameters and piezometric heads. Numerical simulations assisted in estimating average groundwater inflows at certain stages of the proposed mine development. The simulated mine groundwater inflow volumes were used as input into the design of the dewatering measures to ensure a safe mining environment.

Abstract

The Birimian and Tarkwaian rocks of the Paleoproterozoic West African Shield host some of the most important gold reserves in the world, with Ghana the world's 10th largest gold producer and the region collectively producing more gold than all but five countries in the world. The gold was deposited during successive hydrothermal sulphide alteration events, which were channelled by shear zones and thrusts formed during the regional progressive Eburnean tectono-thermal deformation event. The hydrothermal fluids were auriferous and sulphide-rich, resulting in two distinct types of gold and sulphide mineralisation: (1) gold-bearing quartz- and quartz-ankerite veins, occurring in NNE-SSW trending shear zones or thrust folds, usually in Birimian metasediments, with associated sulphides deposited on the fragmented wall rock and (2) disseminated gold-bearing pyrite and arsenopyrite, occurring in halos within the same shear zones or thrust folds as the quartz veins. The sulphidic nature of the gold deposit leads to a high risk of acid rock drainage (ARD). During operations, inflowing groundwater may carry the ARD into underground workings and opencast pits. Post-closure, as the groundwater rebounds, there is a risk of acidic pit lakes forming or acidic decant of underground mines. However, the occurrence of ARD in such systems can be predicted by a combination of weathering profiling, mineralogical profiling and conventional acid base accounting (ABA). The weathering profile can be divided into three zones, readily distinguishable in borehole core: (i) Oxide Zone, from which both the acid-generating sulphide minerals and the acid-neutralising carbonate minerals have been largely leached, (ii) Transitional Zone, from which the carbonate minerals have been largely leached but the sulphide minerals remain, (iii) a Fresh/Primary Zone, where both sulphide and carbonate minerals occur. The Oxide Zone is generally non acid-generating, the Transitional Zone is acid-generating and the Fresh Zone is potentially acid-generating, depending upon the balance of sulphide vs carbonate minerals. Mineralogical profiles can be prepared from the relative abundance of macroscopic sulphide and carbonate minerals in the borehole core, again providing an assessment of ARD risk. Combined logs can then be prepared from these profiles with acid-generation and neutralisation data from ABAs, illustrating in space where the highest ARD risk zones are located. Using this information, groundwater and mine water management options can be developed for operations and closure, such as prioritisation of open pit backfilling or which levels of an underground mine water should be preferentially excluded from.