Conference Abstracts

All Abstracts were presented at the Groundwater Conferences

Displaying 101 - 150 of 795 results

Title	Presenter Name	Presenter Surname	Area	Conference year Sort descending	Keywords
Comparison Of Analytic And Numerical Estimations Of Groundwater Drawdown Evolution For Open Pit Dewatering	Jaco	Nel	Kolwezi, Democratic Republic of the Congo	2013	dewatering, Drawdown
Abstract A new mining site situated near Kolwezi in the Democratic Republic of the Congo plans to develop a pit in phases over a period of six years. The mine requires dewatering volume estimates of the pit as well as a constant water supply to the plant. Hydrogeologic data available at the site during the scoping phase was limited to a few water level measurements and blowout yields from only five hydrological boreholes. Hydraulic properties from reports at neighbouring sites were extrapolated to the geological units at the site. The depth to water level at the site is about 20 m, with a planned final pit depth of approximately 180 m below surface. Based on the limited data available an analytical approach to estimate the inflow into the mine was adopted. Analytical calculations proposed by Marinelli and Niccoli (2000) were used to estimate the inflow into the Pumpi mine pits. The analytical calculations consider recharge, depth of mining vertical and horizontal hydraulic conductivities. Drawdown evolution of pit dewatering are obtained by using different mining depths at different mine stages. The output results from the analytical calculations are the maximum extent of influence of the pit as well as the volume of water inflow into the pit. Limitations of the analytical equations are that they, amongst others, cannot consider complex boundaries. Drilling and pump testing to obtain local hydraulic properties and boundary conditions are planned during the first quarter of 2013. The numerical model will be set up after the drilling and pumping tests, using the new data for calibration. The numerical model will contain as much of the physical layer definitions and potential internal boundaries as possible with model boundaries incorporated along far field fault zones and hydraulic boundaries. The numerical model should improve the reliability of estimates of pit inflow and water supply to the plant. The results between the analytical and numerical approaches can then be compared to improve future dewatering estimates with limited data. It is expected that the reliability of the analytical predictions will reduce after year 4, where the role of boundaries are expected to influence the drawdowns and related flow towards the pit.
An Innovative Application Of The Mixing Cell Model To Quantify Surface Water–Groundwater Interaction	Amy	Allwright	National	2013	Innovation, groundwater resource management, baseflow
Abstract The significance of a reliable groundwater resource assessment is of growing importance as water resources are stretched to accommodate the growing population. An essential component of a groundwater resource assessment is the quantification of surface water–groundwater interaction. The insufficient amount of data in South Africa and the apparent lack of accuracy of current estimates of the groundwater component of baseflow lead to the investigation of a new method. This applicability of this new approach, the Mixing Cell Model (MCM), to quantify the groundwater contribution to baseflow is examined to assess whether the method would be of use in further groundwater resource assessments. The MCM simultaneously solves water and solute mass balance equations to determine unknown inflows to a system, in this application the groundwater component of baseflow. The incorporation of water quality data into the estimation of the surface water–groundwater interaction increases the use of available data, and thus has the ability to increase the confidence in the estimation process. The mixing cell model is applied to datasets from the surface water–groundwater interaction test site developed by the University of the Free State, in addition to data collected along the middle Modder River during a fieldwork survey. The MCM is subsequently applied to a set of quaternary catchments in the Limpopo Province for which there are available calibrated estimates of the groundwater component of baseflow for the Sami and Hughes models. The MCM is further applied to the semi-arid quaternary catchment D73F to assess the applicability of the mathematically-based MCM in a flow system within a regionally-defined zero groundwater baseflow zone. The results indicate that the MCM can reliably estimate the groundwater component of baseflow to a river when sufficient data are available. Use of the MCM has the potential to evaluate as well as increase the confidence of currently determined groundwater baseflow volumes in South Africa, which will in turn ensure the responsible and sustainable use of the countries water resources.
Effects Of Dolerite Intrusions On The Geohydrology Of Upper Karoo Sediments In The Elundini Area, South Africa	Jakobus	Prinsloo	The Elundini Area, South Africa	2013	Geohydrology
Abstract The Karoo Supergroup has a hydrogeological regime which is largely controlled by Jurassic dolerite dyke and sill complexes. The study area is located in the north-eastern interior of the Eastern Cape Province, close to the Lesotho border. The sedimentary rocks of the upper Karoo constitute fractured and intergranular aquifers, due to relatively hydro-conductive lithologies. The main groundwater production targets within the upper-Karoo are related to dolerite intrusions that have a number of characteristics that influence groundwater storage and dynamics. Magnetic, electromagnetic and electrical resistivity geophysical techniques are used to determine the different physical characteristics of the dolerite intrusions, such as size, orientation and the level of weathering. Trends in the data collected from a large-scale development programme can provide evidence that intrusion characteristics also play a role in determining the hydrogeological characteristics of the area. Interpreted geophysical borehole drilling, aquifer testing and water chemistry data can be used to indicate hydrogeological differences between dolerite intrusion types. Observed trends could be used for more accurate future well-field target areas and development.
How Good Is Your Consultant? A Laymens’ Guide To Critically Assessing Consultants	ME	Convery	National	2013	Consultant
Abstract With increasing focus on wasted expenditure within local government and recent media reports on the money spent on poor quality service, it is becoming progressively important for those in a position of engaging consultants, either for groundwater supply or environmental work, to have confidence in the company or person they have employed. This paper focuses on how to assess consultants before they walk through the door based on qualifications, CVs, professional registrations and previous work experience. It goes through the project lifestyle, explaining in a non- technical fashion the different processes involved in a groundwater supply or groundwater contamination assessment and provide simple indicators of good practice that should be evident in the consultant's work. Topics covered include assessing proposals, gathering background information, health and safety, appointing sub-contractors, data quality, the use of appropriate published procedural guidelines, the use of relevant quality guidelines and what deliverables should be provided.
Spoils Handling From Coal Mines In The Waterberg Coalfield Area, Limpopo	Nequita	MacDonald	Limpopo	2013	coal mine, Open pit mines
Abstract The 11 coal-bearing zones currently being mined at Exarro's Grootegeluk mine, discard intraburden onto discard dumps. During mining operations the open pit will be backfilled with plant discards, overburden and interburden on completion of mining. The plant waste will be covered with overburden and topsoil. Intraburden spoils consist of sandstone, mudstone and shale rich in minerals such as pyrite and siderite. These intraburden spoils thus have the capacity to generate acid when exposed to the appropriate conditions. The oxidation of iron sulphides (Pyrite (FeS2)), present within the discard dumps and stockpiles, can influence the hydrochemistry by generating acid-mine drainage, while siderite (FeCO3) can have a basic effect to the immediate surroundings. Acid-base- accounting done on samples gathered from different boreholes in the Waterberg coalfield helped to determine lithological units that can generate acid, with specific regard to the interburden removed and placed on the discard dumps, the interburden used in the pit as backfill, and the acid generation possibility from coal seams in stock piles. This indicated the zones that are more prone to acid- and base-producing potentials. Mineralogical investigations with X-ray diffraction and X-ray fluorescence gave a better record of minerals and elements present in trace amounts within interburden zones that could also have additional problems during storage and use. The areas that possess the highest risk regarding acid generation are the zones enriched in pyrite, as well as the coal seams from stock piles. The management plan for the acid generating spoils of the area has two possibilities: Firstly where acid producing potentials are higher, spoils should not be used where it will be exposed to oxygen and water for long periods of time, as the amount of acid generated cannot be controlled. A second option would entail the immediate compaction and flooding of the mined area so that the amount of acid produced would be controlled and limited.
Quenching A Thirsty Country	Fanus	Fourie	National	2013	Groundwater, strategy, Boreholes
Abstract Only 40% of all the available groundwater resources are developed in South Africa and the development of surface water are becoming more costly and challenging. The Minister of Water and Environmental Affairs acknowledge this and identified the need to increase the use of groundwater as one of the interventions to address the increasing water requirement of towns and communities. Over the last seven years the Department of Water Affairs developed many reconciliation strategies for the area of water management, the big metro municipalities and for the smaller towns and villages in South Africa. The reconciliation strategies entails, among other things, sustainable ways to source additional water supplies for the selected towns/metro’s or villages. Groundwater played a major role in the recommended interventions. The challenges are now the implementation of the groundwater schemes and sustainable management of the groundwater resources. Or differently put: the balancing act between selling of groundwater and the prevention of over-abstraction. The bankability of regional schemes, the credibility of groundwater as a bulk scheme source, poor management of boreholes/well-fields, institutional responsibility, acceptable quality and treatment of groundwater, still challenge the use of groundwater development. Groundwater need to play its role in addressing the future water needs of South Africa, or can it?
Sampling Protocol Optimisation Using Fluid Electrical Conductivity Logging	Candice	Lasher	National	2013	Electrical conductivity, Sampling Protocol
Abstract Characterisation of fracture positions is important when dealing with groundwater monitoring, protection and management. Fractures are often good conduits for water and contaminants, leading to high flow velocities and the fast spread of contaminants in these conduits. Best practice guidelines related to groundwater sampling suggest that specific depth sampling with specialised bailers or low flow purging are the preferred methodologies to characterise a pollution source. These methods require knowledge about the fracture positions and, more importantly, flow zones in the boreholes. Down-the-hole geophysical and flow logging are expensive, complicated and time consuming. Not all fracture zones identified with geophysical logging seem to contribute to flow through the borehole. An efficient and cost-effective methodology is required for the characterisation of position and flow in individual fractures. This research reviewed the use of Fluid Electrical Conductivity (FEC) logging to assist with the development of a monitoring protocol. FEC logging proved to be beneficial as it provided individual fracture positions, fracture yields and vertical groundwater flow directions. FEC logging proved to be fast, cost-effective and practical in deep boreholes. The technique allows the development of a site-specific sampling protocol. The information so obtained assists with the identification of the appropriate sampling depths during monitoring.
The Geohydrological Status Of The Vanrhynsdorp Karst Aquifer	Jana	Brits	Vanrhynsdorp	2013	Geohydrological, Aquafer
Abstract The aim of this study was to determine the geohydrological status of the aquifer within the boundaries of the Vanrhynsdorp Water User Association with emphasis on the central catchment, E33F. This will assist the Department of Water Affairs with the introduction of compulsory groundwater-use licensing and empowerment of the Vanrhynsdorp Water User Association to manage the resource. In this study emphasis was given to the determination of the water balance and groundwater reserve of the central catchment and the designing of a representative groundwater monitoring network. A literature study of five projects conducted since 1978 was done. Comparisons were made between the data and results of these studies. All the historical data from these studies, as well as the data from the current monitoring programme up until December 2012, were put together and analysed. A conceptual model and groundwater reserve determination, as well as a representative monitoring network, were produced. The study showed a general decline in groundwater levels over a 34-year period. It also showed an increase in rainfall over the last 20 years. Based on the reserve determination and the declining groundwater level in spite of increased rainfall and thus recharge, it was concluded that over-abstraction of groundwater in the study area is taking place. It is recommended that compulsory licensing should be put in place as soon as possible and that no additional groundwater-use licences should be granted in the study area. The installation of flow meters on all production boreholes should be stipulated in the licensing condition. This will assist the monitoring and regulation of groundwater abstraction volumes.
Towards The Effective Management Of Groundwater Resources During Unconventional Gas Mining	Surina	Esterhuyse	National	2013	Unconventional gas
Abstract Unconventional gas mining is a new and unprecedented activity in South Africa that may pose various risks to groundwater resources. According to legal experts, South Africa does not currently have the capacity to manage this activity effectively due to various lacunae that exist in the South African legislation. The possible impacts of unconventional gas mining on groundwater, as well as governance strategies that are used in countries where unconventional gas mining is performed; have been analysed and will be discussed. Based on possible impacts and strategies to manage and protect groundwater internationally, possible governance options for the management of South Africa’s groundwater resources are proposed
Development Of The Evander Goldfields 3-D Mine Void Model	Martin	Holland	The Evander Goldfield, Mpumalanga	2013	development, gold mining
Abstract POSTER The Evander Goldfield basin has been mined since the early 1950s at depths between 400 and 2 000 m below ground and is detached from the larger Witwatersrand basin. The assessment and prediction of mine water rebound has become increasingly important for the gold mining industry in the Witwatersrand basin as more mine shafts mothballs and dewatering ceases. The development of a 3-D mine void model is crucial in predicting the rate of flooding as the prediction of the groundwater rebound is primarily driven by the volumes of mine voids along with the amount of recharge. All available mine plan data for the Evander Gold Mine (EGM) were obtained digitally from Harmony Gold. However, the majority of the old mine workings (e.g. Leslie and Winkelhaak) were available as 2-D data and elevations of the mine developments (stopes and drives) had to be captured from hardcopy plans. Data from the more recent mining operations (e.g. Shaft 6), including updated survey and mine plan data, were directly used for the development of the 3-D void model. The calculated mine void volume, based on the EGM operations mine plan data, is approximately 80 518 045 m3. The mine void calculations were checked against the total tons of rock milled by the EGM operations since the late 1950s and was considered valid estimations of the EGM mine void volume. The validated EGM 3-D mine workings plan was subsequently used to determine the stage- volume relationships. The 3-D mine void model established, will then be incorporated into a regional numerical groundwater flow model to be calibrated against observed abstractions and water levels and utilised to predict future dewatering rates.
Complementary use of electromagnetic frequency domain and electroseimic survey methods in groundwater exploration in Zimbabwe.	Joseph M	Zulu	Zimbabwe	2015
Abstract Complementary use of electromagnetic frequency domain and electrosiesmic geophysical exploration methods in groundwater exploration in Zimbabwe. Joseph M Zulu, Josrum Enterprises No. 129 A Fort Street, Albion Flats, 2nd Floor, Office Suite 5 Room 3, Bulawayo, Zimbabwe. Email Address: [email protected]. Abstract Geophysical survey methods and divining are commonly used in groundwater exploration. In view of the current costs of drilling boreholes and fear of drilling a dry borehole, most people prefer the use of geophysical survey methods to have their boreholes sited. Some prefer the use of diving methods for initial siting and then confirmation of the identified site using geophysical survey methods. The key principle being complementarity of the methods to confirm the presence of water at the identified site. Electrical resistivity method and electromagnetic frequency domain methods are popular in ground water exploration in Zimbabwe, with electrical resistivity being the method of choice by many investigators. A new approach in groundwater exploration is proposed where complementarity of geophysical methods is exploited. A complementary approach of using geophysical methods in conjunction with geology, where two methods are used in investigating a site is proposed. In the study the latest technology in groundwater exploration, electrosiesmic survey method was used to complement the electromagnetic frequency domain method in various geological environments. Electromagnetic profiles were carried out on the target areas. Inversion was done on the collected and results presented as a pseudo section. Anomalies identified were further investigated using electrosiesmic sounding. The results of the sounding were presented in the form of a sounding curve. The subsurface layer thicknesses were calculated using forward modelling assuming the typical seismic velocity values of waves generated when passing through geological formations in the areas under investigation. The geology of areas studied include granite, greenstone, Kalahari sands, sandstones, mudstones and basalt of the Karoo stratigraphy. The approach produced impressive results. High yielding borehole sites were identified and successfully drilled in areas where it had been accepted that it was difficult to get water or in areas where it had been accepted there was no groundwater. Comparison of driller's log with models generated from geophysical survey results was also done. Key words: electromagnetic, electroseismic, geology, complementarity, groundwater. I acknowledge that this work has not been published elsewhere.
Hydrogeochemical processes in the shallow aquifer of the Lubumbashi river basin: multivariate statistical approach	Antoine	Lumu Moussa		2015
Abstract Understanding the hydrogeochemical processes that govern groundwater quality is important for sustainable management of the water resource. A study with the objective of identifying the hydrogeochemical processes and their relation with existing quality of groundwater was carried processes in the shallow aquifer of the Lubumbashi river basin. The study approach includes conventional graphical plots and multivariate analysis of the hydrochemical data to define the geochemical evaluation of aquifer system based on the ionic constituents, water types, hydrochemical facies and groundwater factors quality control. Water presents a spatial variability of chemical facies (HCO3- - Ca2+ - Mg2+, Cl- - Na+ + K+, Cl- - Ca2+ - Mg2+ , HCO3- - Na+ + K+ ) which is in relation to their interaction with the geological formation of the basin. The results suggest that different natural hydrogeochemical processes like simple dissolution, mixing, and ion exchange are the key factors. Limited reverse ion exchange has been noticed at few locations of the study. At most, factor analyses substantiate the findings of conventional graphical plots and provide greater confidence in data-interpretation. {List only- not presented}
The value (or not) of measuring redox potential in groundwater: A case study	Meris	Mills		2015
Abstract The redox state of groundwater is an important variable for determining the solubility and mobility of elements which can occur in different redox states at earth surface conditions, such as Fe, Mn, Cr, As, U, N, S, V etc. Eh-pH diagrams are potentially invaluable for understanding and predicting the behaviour of these redox species yet, unlike pH, redox is seldom a routine field parameter due to the difficulties in measurement and interpretation. This paper discusses the potential use and limitations of field measurements of the redox state of groundwater with specific reference to the geochemical behaviour of dissolved iron in the Table Mountain Group (TMG) aquifer. As part of an investigation into iron cycling within the TMG aquifer, the redox state of groundwater was estimated through three different methods, namely direct in-situ measurement of Eh, direct measurement of DO and calculation from iron speciation in groundwater. Comparison of the results from the three methods highlights the potential value of collecting redox data, but also the complexity of controls on redox potential. The redox measurements allowed the determination of the controlling reactions on iron mobility within the TMG, but only by using the iron speciation method to calibrate the in-situ values and thereby identify which redox pair was controlling redox equilibrium. As this requires measurement of redox ion pairs in solution, it is unlikely to become a routine method for redox assessment, unless the specific redox state of an element is critical in understanding its mobility. For the majority of groundwater site investigations, measurement of the dissolved oxygen content of groundwater is probably sufficient as a first pass.
TEMPEST for groundwater exploration	Odirile	Dingoko	Australia	2015	Airborne electromagnetic surveys
Abstract In recent years there has been renewed interested in identifying and understanding groundwater resources. Airborne electromagnetic (AEM) surveys can provide useful, cost effective information about the geometry of aquifers and their host rocks. TEMPEST is a fixed wing AEM system which has been used extensively for groundwater applications. The system possesses many attributes which aid in groundwater exploration including: broad operational bandwidth; multifaceted software approach; and, a distinctive calibration technique. These features allow both shallow and deep subsurface features to be imaged which aid in mapping groundwater aquifers along with the broader groundwater subsystem. This paper will review TEMPEST surveys flown for the Western Australian Department of Water (DoW) for the purpose of groundwater characterisation. The surveys were focussed on the identification of geological contacts, subsurface aquifers and seawater intrusion extents. The survey data was interpreted using an integrated approach which involved reviewing the newly acquired geophysical data, identifying contacts and anomalous features in the acquired data, reviewing existing geological and geophysical data in the area and correlating features identified in acquired data to known geology. The first case study was flown over the North Gnangara area of the Perth Basin with the primary aim of defining the spatial distribution of clay and silty layers that impede recharge to the groundwater table. The survey succeeded in achieving its primary aim of identifying the distribution of clay layer targets. Through the integrated interpretation approach it was also successful in achieving its secondary aims by clearly defining the contact between superficial units and the underlying stratigraphy, identifying key structures within the basin, outlining the top of the seawater intrusion, and mapping confining strata within the deeper aquifer systems in the Perth Basin. The second case study was flown over the lower reaches of four river systems in the North Pilbara coast with the aim of understanding the aquifer geometries and groundwater salinity distribution within the region. The primary aims of the survey were achieved and provided a basement geology map, relative porosity maps, approximate weathered and unweathered bedrock surfaces as well as the approximate geometry of the seawater intrusion within all survey areas. It was also possible to map the interpreted extents of alluvial aquifers within two of the river systems as well as the contact between two sandstone aquifers present in one of the river systems. These case studies show that the TEMPEST AEM system can provide valuable information about the geometry of aquifers and their host geology. AEM surveys should be used as an initial method for determining broad aquifer geometry and the identification of priority areas prior to further less cost effective water bore drilling.
Monitored Natural Attenuation on-sites with different geological setting	Bongani	Masombuka		2015
Abstract When considering how to reduce contamination of petroleum hydrocarbons in shallow aquifers, it is important to recognize the considerable capacity of natural processes continuously at work within the secondary sources of contamination. This natural processes are technically referred to as Monitored Natural Attenuation (MNA), a process whereby petroleum hydrocarbons are deteriorated naturally by microbes. This approach of petroleum hydrocarbon degradation relies on microbes which utilise oxygen under aerobic processes and progressively utilises other constituents (sulphates, nitrates, iron and manganese) under anaerobic processes. MNA process is mostly evident when light non-aqueous phase liquids (LNAPLs) has been removed while the dissolved phase hydrocarbon compounds are prominent in the saturated zone. The case studies aim at determining feasibility and sustainability of Monitored Natural Attenuation process at different sites with varying geological setting.
Hydrogeology of the Cedarville Flats primary aquifer, Upper Umzimvubu River Basin, South Africa	Molla	Demlie	Eastern Cape	2015	Cedarville Flats alluvial aquifer, Environmental Isotopes, highland recharge, residence time
Abstract The Cedarville Flats aquifer located in the Upper Umzimvubu River Basin, Eastern Cape Province is a source of water supply for an important agricultural region in South Africa. The hydrogeology of this important aquifer is investigated to understand the occurrence, circulation, recharge and quality of groundwater. To this end, local and regional geology, borehole lithological logs, borehole yields, aquifer hydraulic characteristics (including aquifer thickness, water level, hydraulic conductivity, transmissivity and storage coefficient), hydrometeorological, hydrochemicaland environmental isotope data were collected and interpreted. The results show that the alluvial aquifer is made up of sand, gravel, boulders and clay and its thickness reaches 51 meters in places. Median hydraulic properties indicate that the Cedarville Flats primary aquifer is the most productive aquifer compared to the underlying Molteno and Burgersdorp Formations. It has an estimated median borehole yield in the order of 6 l/s as compared to 2 l/s for the Burgersdorp and 1.5 liters for the Molteno Formations. The aquifers in the area receive an estimated 7% of rainfall recharge. The groundwaters of the area are characterized by low ionic concentration with EC and TDS ranging from 235 to 285 ?S/cm and from 65 to 151 mg/l, respectively. The hydrochemical data further indicate a groundwater hydrochemical facies of either Ca-Na-Mg-HCO3 or Na-Ca-Mg-HCO3 highlighting a typically less evolved recharge area groundwater having short residence time and hence less water-rock interaction. Springs and artesian wells show a relatively depleted stable isotope and very low to dead tritium signals indicating high altitude recharge and longer circulation path and residence times compared to wells tapping the water table aquifer which indicate young water with recharge coming from the immediate surrounding area. Similarity in hydrochemical and stable isotope signatures between the streams that drain across the alluvial flats and the shallow groundwaters mean that there is a close interconnection between surface water and groundwater in the area.
The use Vegetable Oil Substrate's in the treatment of contaminated groundwater	Michelle	Pienaar		2015
Abstract Edible vegetable oil (EVO) substrates have been successfully used to stimulate the in situ anaerobic biodegradation of groundwater contaminated chlorinated solvents as well as numerous other anaerobically biodegradable contaminants like nitrates and perchlorates at a many commercial, industrial and military sites throughout the United States of America and Europe. EVO substrates are classified as a slow release fluid substrate, and comprise of food grade vegetable oil such as canola or soya bean oil. The EVO substrate serves as an easily biodegradable source of carbon (energy) used to create a geochemically favorable environment for the anaerobic microbial communities to degrade specific contaminants of concern. EVO substrate's can either be introduced into the subsurface environment as pure oil, in the form of light non aqueous phase or as an oil/water emulsion. The emulsified vegetable oil substrates holds several benefits over non-emulsified vegetable oil as the fine oil droplet size of the commercially manufactured emulsified oils can more easily penetrate the heterogeneous pore and fracture spaces of the aquifer matrix. The use of this technology to stimulate in situ biodegradation of groundwater contaminants is still relatively unknown in South Africa. This paper will give an overview of the EVO technology and its application, specifically looking at the advantages of using this relatively inexpensive, innocuous substrate based technology to remediate contaminated groundwater within fractured rock environments commonly encountered in South Africa. {List only- not presented}
Use Of Environmental Isotopes To Determine Hydraulic Connectivity Across The Surrounding Aquifers At Majuba UCG	Gundo	Mathoho		2015
Abstract Environmental isotope techniques have been successfully applied in the field of hydrogeology over the last couple of decades and have proved useful for understanding groundwater systems. This paper describes a study of the environmental isotopes for Oxygen (18O) and Hydrogen (1H, 2H-Deutrium, 3H-Tritium) obtained from various points in and around the underground coal gasification (UCG) site in Majuba, South Africa. UCG is an alternative mining method, targeting deep coal seams that are regarded as uneconomical to mine. The process extracts the energy by gasifying the coal in-situ to produce a synthetic gas that can be used for various applications. The site consists of shallow, intermediate and deep aquifer systems at a depth of 70m, 180 and 300m respectively. The intermediate aquifer is further divided into the upper and lower aquifer systems. Samples were taken from each aquifer system together with supplementary samples from the Witbankspruit and an on-site water storage dam. A total of 15 samples were submitted for isotope analyses. By investigating the various isotopic signatures from all the samples taken, it will be possible to determine if there are similar or contrasting isotopic compositions by deducing possible water source for each sample due to isotopic fractionation caused by physical, chemical and biological processes. This will also be supported by deducing the mean residence time (MRT) for each water source sampled based on the Tritium data as well as the chemistry data already available for different sources. The chemistry data established linkages between the upper and lower intermediate aquifers.{List only- not presented} Key words: Environmental isotopes, UCG, Water source, Isotope fractionation
Blast curtain optimized with a numerical model for TSF seepage control	Robel	Gebrekristos		2015
Abstract Preventing the spread of seepage from tailings storage facilities (TSF's) in groundwater is necessary as it often contains toxic contaminants. Experience has shown that seepage from TSFs is inevitable and that zero seepage remains difficult even with complex liner systems. Multiple seepage control methods are often required to minimise seepage to ensure that environmental regulations are met. Control methods can be grouped into either barrier or collection systems. Barrier systems are used to hinder seepage whereas collection systems are used to intercept seepage. A blast curtain, which is the focus of this article, is a type of collection system that is still at a conceptual level but has seen little or no application worldwide. It works in principle, similarly to a curtain drain, but is typically extended to greater depths depending on the aquifer vulnerability. Numerical modeling has shown that this mitigation measure could add another line of defence for seepage control. The depth and effectiveness of the curtain can be optimized with a numerical model to ensure optimal interception of contaminated seepage around the TSF. Depths of up to 30 m in fractured aquifers have been simulated in this study. A blast curtain is constructed by drilling a set of boreholes around a TSF in close proximity to one another and then fracturing the rock using either explosives or fracking methods to create a more permeable zone. This is then combined with a series of scavenger wells or natural seepage to abstract the contaminated water. Numerical simulation has shown that blast curtains are effective especially if groundwater flow is horizontal. The effectiveness decreases if the vertical flow component is significant. A blast curtain can result in the lowering of the water table, however, local depression is a less of a concern than potential groundwater contamination. {List only- not presented}
Unravelling the complex geohydrological structure of the Elandsfontein aquifer unit	Kezia	Smith	Western Cape	2015
Abstract The Elandsfontein aquifer is currently under investigation to assist with the management of the system and to ensure the protection of the associated Langebaan lagoon RAMSAR site. The Elandfontein aquifer unit is situated adjacent to the Langebaan Road aquifer in the Lower Berg River Region and is bounded by the Langebaan Lagoon, possible boundary towards Langebaan Road aquifer, the Groen River bedrock high and the Darling batholith. The study will investigate the boundaries and hydraulic characteristics of the different aquifers and aquitards (Elandsfontein clay layer) in the Elandsfontein unit and their relationship to the Langebaan Lagoon. A literature review and baseline study has been completed to determine groundwater flow patterns and the general distribution of water quality, using historic data to characterize the different aquifers and aquitards of the system. An initial conceptual model has been formulated based on this data. Pumping tests will be used to acquire hydraulic characteristics of the Elandsfontein aquifer where data gaps exist, together with water quality and stable isotope sampling. Future plans are to construct a groundwater numerical flow model of the Elandsfontein system to assist with the management of the complex relationships between the recharge areas, flow paths through the different aquifer layers and aquitards towards the Langebaan Lagoon discharge. Results will be presented using graphical methods such as time series graphs amongst the monitoring boreholes over the years, piper diagrams to show water type characterization (Na-Cl type water) and initial results from the groundwater flow model. The expected results are envisaged to advance knowledge on groundwater availability and quality to inform the decision about water resource protection and utilization. Therefore this study is designed to provide large-scale background information that will improve the knowledge and understanding of the Elandsfontein aquifer unit and provide a basis for potential future studies of a more-detailed nature.
Hydrogeochemical Evolution of an Opencast Colliery After Decommissioning - Static vs. Dynamic Prediction	Altus	Huisamen	Mpumalanga	2015
Abstract Static indicator tests, such as acid-base accounting, are commonly used to provide an indication of ARD potential of backfill material in opencast coal mines. This potential for acidity is then commonly incorporated into numerical models, wrongfully, as a constant contamination source with the maximum possible sulphate being released from the pit, ad infinitum, which is, obviously, not the case. Dynamic tests on the other hand, are considered superior, but are expensive and time consuming. The proposed alternative approach is geochemical modelling, illustrated by a case study in the Mpumalanga coal fields. A decommissioned colliery near Carolina, Mpumalanga, was recently confronted with the prediction of the impacts that its backfilled opencasts might have on groundwater in the long term with regards to acid and contaminant generation, demanding a more realistic and well-defined conceptual and numerical approach than the simple minimum screening method. This study utilised the integration of a well-defined conceptual model, mineralogical data, acid-base accounting data, leaching test data, literature and groundwater monitoring data to address the long term hydrogeochemical evolution of groundwater at the colliery, using transiently calibrated geochemical and numerical flow models. Using the mineralogical data available from samples collected, as well as the sulphur content identified by ABA, a standard error was calculated for the abundances of all mineral phases present along with mean weight percentages, defining the likely boundaries of mineral abundances. Using these values along with reactive surface areas calculated from average grain sizes, using a collapsing core model, as well as rate constants from literature, the fluid rock interaction in the leaching tests was simulated and calibrated against leaching test results in the geochemical model, by varying mineral abundances, reactive surface areas and rate constants within the statistically acceptable boundaries. Once a calibrated mineral assemblage was identified using this method, the assemblage was geochemically modelled in the natural environment, after calculation of fluid to rock ratios, which in this case was purely potential backfill porosity vs. recharge due to the natural groundwater level being below the pit base, as well as potential oxygen fugacity. The calculated concentrations of constituents were then introduced into a transiently calibrated numerical flow and transport model via recharge concentrations, to also chemically calibrate this model. The chemical calibration was successful within a 20 mg/L range, illustrating the reliability of the conceptual and geochemical models, but also the reliability of predicted numerical modelling results. Based on the available data and modelling results, the colliery would not have a future impact on groundwater with regards to ARD and metals. However, elevated major cation and anion concentrations are expected, calculated within order of magnitude accuracy, and can be managed according to dynamic and realistic models, instead of a static worst case scenario.
Groundwater Monitoring During An Underground Coal Gasification Process	Johan	van Dyk		2015
Abstract Underground Coal Gasification (UCG) is an emerging, in-situ mining technology that has the advantage to access a low cost energy source that is currently classified as not technically or economically accessible by means of conventional mining methods. As such it offers significant potential to dramatically increase the world's non-recoverable coal resource. Groundwater monitoring in the South African mining industry for conventional coal mining as an example, is well established, with specific SANS, ASTM and ISO Standards dedicated for the specific environment, location and purposes. In South Africa a major impact of the coal mining industry can be a reduction in the groundwater quantity and quality. South-Africa's groundwater is a critical resource that provides environmental benefits and contributes to the well-being of the citizens and the economic growth. Groundwater supplies the drinking water needs of a large portion of the population; in some rural areas it represents the only source of water for domestic use. Utilization and implementation of groundwater monitoring programs are thus non-negotiable. The groundwater quality management mission, according to the Department of Water and Sanitation in South-Africa, is set in the context of the water resources mission and is as follows: "To manage groundwater quality in an integrated and sustainable manner within the context of the National Water Resource Strategy and thereby to provide an adequate level of protection to groundwater resources and secure the supply of water of acceptable quality." The scope of this paper is to propose an implemention strategy and a fit-for-purpose groundwater monitoring program for any Underground Coal Gasification commercial operation. It is thus important to pro-actively prevent or minimise potential impacts on groundwater through long-term protection and monitoring plans. A successful monitoring program is one that consists of (1) an adequate number of wells, located at planned and strategic points; (2) sufficient groundwater sampling schedules; and (3) a dedicated monitoring program and quality control standard. In order to have an efficient monitoring program and to prevent unnecessary analysis and costs, it is also critical to determine upfront what parameters have to be monitored for the specific process and site conditions.
Existing Springs in City of Cape Town and Environs: Spring Use Strategy	Louise	Soltau	Western Cape	2015
Abstract Cape Town... Home to over 3 and a half million people, the second most populated city in South Africa was born in the shadow of the Table Mountain. The mountain offered all the elements vital for human settlement... most importantly WATER. The reports of the abundance of fresh water and fertile land at the foot of the mountain and surrounds inspired the VOC to set up a refreshment station at the Cape. By the late-1800s, spring water was solely used for domestic supply to the settlers of Cape Town. Until the 1930s, the Stadsfontein or Main Spring was still being used as a source of drinking water but because of on-going concerns about the safety of the water for human consumption, and sufficient water being available from the new schemes like Steenbras and Wemmershoek, a decision was taken to discontinue using the Stadsfontein for drinking water purposes. Since then most of the water joined the stormwater to the sea, until 2010 when the City recommenced using the water for irrigation at Green Point Stadium and the Commons. City of Cape Town faces a number of water supply challenges. These include managing the ever increasing demands on the current water supply. The City of Cape Town Springs Study was born from this 2001 Water Demand Management study and it aims primarily to examine the possibility of using spring water as an alternative source of water for non-potable supply. Of these, the springs which hold the most potential for use are found in two areas - the CBD area of Oranjezicht, home to the Field of Springs
Platinum mines will leave behind a sustainable legacy which will form a vital building block to meet future water demands	Fanie	Botha		2015	aeration and aerobic storage facilities, Nitrate
Abstract Slightly more out of the box idea is the use of anthropogenic aquifers as storage and chemical conditioners. This concept was first introduce by Eland Platinum Mine(EPM) and reported on in previous papers. At EPM water is used through a serious of natural aeration and aerobic storage facilities to reduce nitrate levels. In 2013 another group introduced pilot studies by virtue of abstraction in support of the water conservation and demand management strategy; which has proven that it could enable the operations to overcome water shortage periods and reduce pressure on Rand Water (RW). The pilot sites would deliver water into the dirty water circuit, but within five to ten years it may further be used to overcome months with zero potable water supply. . In platinum mines the more the aquifers are used the cleaner the water becomes, simply because introduced pollutants are not constant sources and country rock is mostly inert. In the future these aquifers have the potential to become larger storage facilities protected from floods and limited evaporation losses. It is foreseen that some of the mines in the western belt may have more water stored in primary aquifers than water stored within major water dams. Yields from these aquifers for individual aquifers may be up to 450 m3/hour and storage of 18 Mm3. . Why then this paper if we are already using it? The issue is that the true value of these aquifers an only be unlocked when they are used as recharging aquifers and thereby actively storing dirty water within a dirty water aquifer. Once we are able to undertake this the positive environmental gains such of environmental overflows, condition dirty water, reduction of pollution and significant reduction of the use of potable water from RW. {List only- not presented}
Stampriet Transboundary Aquifer System	Joyce T	Leshomo	SADC	2015	IAH, Unesco-IHP, transboundary aquifers
Abstract The International Association of Hydrogeologists and UNESCO's International Hydrological Programme have established the Internationally Shared (transboundary) Aquifer Resource Management (ISARM) Programme. This multiagency cooperative program has launched a number of global and regional initiatives designed to delineate and analyze transboundary aquifer systems and to encourage riparian states to work cooperatively toward mutually beneficial, sustainable aquifer development and management. The Stampriet Transboundary Aquifer System was selected as one of the three case studies funded by UNESCO. The Stampriet Aquifer System is located in the arid part of the countries (Botswana, Namibia and South Africa) where groundwater is a sole provider for water resource. The area is characterised by the Kalahari (local unconfined aquifer) and Nossob confined aquifer
High Resolution Site Characterisation Assessment Of A Chlorinated Solvent Plume In A Shallow Unconfined Aquifer	Kate	Naude		2015
Abstract Identifying and characterising the vertical and horizontal extent of chlorinated volatile organic compound (CVOC) plumes can be a complex undertaking and subject to a high degree of uncertainty as dense non-aqueous phase liquid (DNAPL) movement in the subsurface is governed most notably by geologic heterogeneities. These heterogeneities influence hydraulic conductivity allowing for preferential flow in areas of higher conductivity and potential pooling or accumulation in areas of lower conductivity. This coupled with the density-induced sinking behaviour of DNAPL itself and the effects of groundwater recharge in the aquifer result in significant challenges in assessing the distribution and extent of CVOC plumes in the subsurface. It has been recognized that high resolution site characterization (HRSC) can provide the necessary level of information to allow for appropriate solutions to be implemented to mitigate the effects of subsurface contamination. Although the initial cost of HRSC is higher, the long-term costs can be substantially reduced and the remedial benefits far greater by obtaining a better understanding of the plume characteristics upfront. The authors will discuss a case study site in South Africa, where ERM has conducted HRSC of a CVOC plume to characterise the distribution of the source area and plume architecture in order to assess the potential risk to receptors on and off-site. The source of impact resulted from the use of a tetrachloroethene (PCE)-based solvent in an on-site workshop. The following methods of characterization were employed: - Conducting a passive soil gas survey to identify and characterise potential source zones and groundwater impacts; - Vertical characterisation of the hydrostratigraphy, contaminant distribution and speciation in real time using a Waterloo Advanced Profiling System (APS) with a mobile on-site laboratory; - Using the Waterloo APS data to design and install groundwater monitoring wells to delineate the vertical and lateral extent of contamination; and - Conducting a vapour intrusion investigation including sub-slab soil gas, indoor and outdoor air sampling to estimate current risk to on-site employees. In less than a year, the risk at the site is now largely understood and the strategies for mitigating the effects of the contamination can be targeted and optimised based on the information gained during the HRSC assessment.
Groundwater Resource Development targeting major fault zones In Banded Iron Formations (BIF) for Augmentation of the Vaal Gamaga	Frans	Wiegmans	Northern Cape	2015
Abstract The mineral rich Northern Cape Province produces 84% of South Africa's iron ore, while the Kalahari basin holds 92% of the world's high grade manganese deposits, with diamond and lime mining operations to a lesser degree. Mining expansion programs and new mines planned in the Northern Cape drive the region's economic development and growth strategy. The planned mining expansion depend on water being available for mining water needs and related increased demands for domestic water supplies. Current water supplies consist of local groundwater resources (boreholes and mine dewatering) and bulk water supply from the Vaal Gamagara (VGG) Pipeline Scheme. In 1992 the Kalahari East water supply pipeline was incorporated to supply domestic and stock water to an area of approximately 1.4 million ha. The VGG scheme consists of 370 km pipes, was built in the late sixties and is nearing its useful life expectancy. Increased water supply interruptions are being experienced while operating at capacity. The pipeline has the capacity to convey and import water of approximately 15 million m3/a into the D41J and D41K quaternary catchments. Water demand projections show an increase to 40.1 million m3/a in 2030. Various options were investigated to upgrade the VGG water supply scheme. One option considers groundwater resources to augment the water from the Vaal River from four indentified target areas (SD1 to SD4). Major fault zones in Banded Iron Formations (BIF) are targeted for groundwater resource development in the SD4 area, located east of Hotazel. This area is largely covered by Quaternary age sand and located near the endpoint of the VGG scheme and therefore prioritized as investigation area. The primary objective of the hydrogeological investigation was to identify the existence of exploitable resources for additional source development. Secondary objectives were to assess the contribution groundwater can make to augmenting pipeline water; providing a source to an area and thus diminish reliance on the pipeline; and providing an independent source, which could prevent the need for pipeline extensions. The paper will discuss the use of an airborne magnetic and Time Domain Electromagnetic's (TDEM) survey combined with gravity ground surveys as a key success factor in adding to the geological and structural information of the area. The paper will also present the results of exploration drilling (> 60 boreholes) over a large area and related borehole test pumping with water sampling to identify a sustainable and potable water supply of 2.5 million m3/a.
An Acid Base Accounting study of the coal-bearing formations in the Waterberg coalfield	Lore-Mari	Deysel	Karoo	2015	coal mine, sulphur, acid base accounting
Abstract Coal constitutes 77% of the primary energy needs in the country, with the Waterberg Coalfield estimated to host about 40% of the remaining South African coal resources. The Karoo coals were deposited in a reduced environment that have the potential to produce sulphides within the sediments they are hosted. The sulphur content within the coal can range from 0.1 wt.% to as high as 10 wt.%. Mining generates a disturbance in the natural groundwater levels and affects the surrounding water chemistry when sulphate is produced as a result of pyrite oxidation. Acid base accounting (ABA) was used to determine the balance between the acid producing potential (AP) and acid neutralizing potential (NP). From the analysis the Net Neutralising Potential (NNP) classified samples as either acid or non-acid producing. ARD does not only result in the generation of acid but is accompanied by decreased pH and increased values of specific conductance, dissolved metals and sulphate. The ABA results showed that interburden and coal samples have higher risks of producing acid upon oxidation than overburden samples. Higher concentrations of neutralising minerals are present in overburden samples. ABA indicated that the material 60m below ground surface had a higher acid producing potential than the material above. The analysis from kinetic tests showed the long-term behaviour of different samples, with the electrical conductivity (EC) and pH changing over time. Samples with lower pH continued to produce more sulphate, while calcium continued to increase until it was depleted from the samples. Inductively coupled plasma analysis determined the release of the heavy metals which can be detrimental to the environment, such as As, Co, Ni and Pb. The water demand will increase as mining continues in the area, with inter-catchment transfers identified to overcome local water scarcity issues. ARD poses a big threat to both groundwater and surface water resources.
Decision making with web-based geo-spatial databases coupled to groundwater models	John	Wise		2015
Abstract Model calibration and scenario evaluations of 2D and 3D groundwater simulations are often computationally expensive due to dense meshes and the high number of iterations required before finding acceptable results. Furthermore, due to the diversity of modelling scenarios, a standardised presentation of modelling results to a general audience is complicated by different levels of technical expertise. Reducing computational time In this presentation we look briefly at the use of Reduced Order Models (ROM's), which is one of the recent developments in groundwater modelling. The method allows significant speed-up times in model calibration and scenario evaluation studies. In saturated flow for example, these approaches show speed-up times of >1000 when compared to full models created with Finite Element of Finite Difference methods. These methods are demonstrated to a case study in the Table Mountain Group, in which we show a simplified parameter calibration and scenario evaluation study. Standardising presentation In order to present the results to as wide an audience as possible, the use of a web-browser as a GUI is proposed, where the web-page is coupled to a geo-spatial database and data is presented in a spatial and numeric format. The use of the spatial database manager PostgreSQL with PostGIS is proposed. Through a browser interface, users can run modelling scenarios using the ROM, which is evaluated in near real-time. Following the evaluation of the model, we show how PostGIS can spatially present data on a base-map such as google maps. In keeping with the current trends in online map customisation, viewers can interactively choose to overlay the base-map with a data-type (such as pressure or hydraulic head contours or flow direction) that is most intuitive for their level of familiarity with the data. Conclusion In using advanced modelling techniques and a simplified browser based presentation of results, high-level decisions in water resource management can be significantly accelerated with the use of interactive scenario evaluations. Furthermore, by reaching a broader audience, public participation will be significantly enhanced.
Effects of Urbanization and Agricultural activities on Aquifer storage and Groundwater quality	Athenkosi	Matshini		2015
Abstract POSTER Aquifer stress arising from urbanization and agricultural activities, these two factors affect aquifer properties when prolonged. Increase in urbanization especially those situated on top unconfined or semi-confined aquifer results in pressure on natural resources, this includes water resources, and changes of land use for agricultural purposes with high economic benefits has an effect on groundwater quality to due to application of Nitrogen- fertilizers during crop rotation and this is largely experienced in developing countries. The effects ranges from groundwater quality to aquifer storage as prolonged aquifer withdrawals due to irrigation, construction, manufacturing affects groundwater storage. Assessment of urbanization and agricultural effects on groundwater requires a complex analysis as integration approaches needs to be discovered for a better analysis of the two more specially when assessing groundwater pollution. The study was conducted to assess the impacts of urbanization and agricultural activities on aquifer storage and groundwater quality: by (a) determining the relationship between the occurrence of contamination due to urbanization by assessing contaminants present in the study area (b) develop groundwater protection, and if any offer recommendation for groundwater management. Multiple-well tests were conducted observing the behavior of drawdown and recovery for assessing groundwater storage. Two aquifer properties were observed to yield information about any changes in aquifer storage (transmissivity and storage coefficient) and groundwater quality lab test focusing on TDS, nitrate and pH were conducted. Historical results reflect that before industrial and urban revolution the groundwater contained small amounts of TDS compared with the present results. Increase in nitrate and pH concentrations observed in location closer to agricultural areas. Prolonged aquifer withdrawals increases expansion of cone of depression and therefore increases aquifer vulnerability and the risk of aquifer being polluted, and this increases storage coefficient. This study can be used to formulate protection zones for water resources and practice towards groundwater management.
The Complexity of Baseline Monitoring in Unconventional Gas Projects	Richard	O'Brien	Karoo	2015
Abstract The subsurface has been likened to a maze due to the intricate and often disconnected pathways contained even in unconsolidated and relatively homogeneous aquifer systems. The weathered fractured aquifers in the Karoo offer unique challenges to those planning monitoring campaigns and provide opportunities for the research community to identify innovative solutions. Careful thought needs to be given to the objectives of monitoring as these can change the requirements of the work. Other important considerations are the location and design of monitoring wells which often needs to be tailored to site specific conditions while the selection of determinands to be analysed introduces yet another layer of complexity. These include questions around the relevant detection limits, representative sampling methods and a host of other aspects. Following prescribed approaches designed for managing traditional industrial processes may not be relevant even though these approaches are based on decades of research and learning from past experience, both good and bad. Careful consideration of the technical detail in advance of beginning any monitoring in the field is essential and even then, as in any hydrogeological assessment, a level of uncertainty will always remain. This presentation will cover the status of planning work on Karoo aquifer characterisation and geochemical assessment of the ambient or baseline conditions. Significant effort continues to be made to tailor fieldwork to site specific conditions and be ready to collect a representative data set when conditions allow. {List only- not presented}
An Analysis Of The Challenges For Groundwater Governance During Unconventional Gas Development In South Africa	Kevin C	Pietersen	National	2015	groundwater governance, Unconventional gas
Abstract The groundwater governance arrangements for the development of groundwater resources were analysed. The analysis highlighted gaps and barriers to overcome before unconventional gas (shale gas and coal bed methane) development can take place at an industrial scale. The following governance challenges were identified (i) setting baseline measurements to detect groundwater pollution and to determine resource status; (ii) review of licenses and setting conditions for the development of unconventional resources; (iii) compliance monitoring and enforcement systems in place (iv) dealing punitively with non-compliant operators (v) mitigation options in place to prevent groundwater pollution; (vi) goal-based regulatory framework in place rather than a prescriptive regulatory framework; (vii) disclosure of hydraulic injection fluid; (viii) coordination with other government departments and regulatory bodies; (ix) a framework for subsidiarity and support to local water management; and (x) an incentive framework that support good groundwater management. To overcome the challenges requires a decentralized, polycentric, bottom-up approach, involving multiple institutions to deal with unconventional gas development. This provides better conditions both for cooperation to thrive and for ensuring the maintenance of such institutions.
Estimation of Groundwater Recharge Response from Rainfall Events in a Semi-Arid Fractured Aquifer: Case study	Phathutshedzo	Nemaxwi		2015
Abstract Estimating groundwater recharge response from rainfall remains a major challenge especially in arid and semi-arid areas where recharge is difficult to quantify because of uncertainties of hydraulic parameters and lack of historical data. In this study, Chloride Mass Balance (CMB) method and Extended model for Aquifer Recharge and soil moisture Transport through unsaturated Hardrock (EARTH) model were used to estimate groundwater recharge rates. Groundwater chemistry data was acquired from the Department of Water and Sanitation (DWS) and Global Project Management consultants, while groundwater samples were collected to fill-in the identified gaps. These were sent to Council for Geoscience laboratory for geochemical analysis. Rainfall samples were also collected and sent for geochemical analysis. An average value of rainfall chloride concentration, average groundwater chloride concentration and mean annual precipitation (MAP) were used to estimate recharge rate at a regional scale. Local scale recharge was also calculated using chloride concentration at each borehole. The results were integrated in ArcGIS software to develop a recharge distribution map of the entire area. For EARTH model, long term rainfall and groundwater levels data were acquired from the South Africa Weather Services and DWS, respectively. Soil samples were collected at selected sites and analysed. These were used to determine representative values of specific yield to use on EARTH model. 60% of the groundwater levels data for 5 boreholes was used for model calibration while the remaining 40% was used for model validation. The model performance was evaluated using coefficient of determination (R2), correlation coefficient (R), Root Mean Square Error (RMSE) and Mean square error (MSE). Regional recharge rates of 12.1 mm/a (equivalent to 1.84% of 656 mm/a MAP) and 30.1 mm/a (equivalent to 4.6% MAP) were calculated using rainfall chloride concentrations of 0.36 and 0.9 mg/L, respectively. The estimated local recharge rates ranged from 0.9-30.2 mm/a (0.14 - 4.6%) and 2 - 75 mm/a (0.3 - 11.4%) using chloride concentration of 0.9 and 0.36 mg/L, respectively. The average recharge rate estimated using EARTH model is 6.12% of the MAP (40.1 mm/a). CMB results were found to fall within the same range with those obtained in other studies within the vicinity of the study area. The results of EARTH model and CMB method were comparable. The computed R2, R, RMSE and MSE ranged from 0.47-0.87, 0.68-0.94, 0.04-0.34, 0.16-3.16, and 0.50-0.79, 0.68-0.89, 0.07-0.68, 0.15-8.78 for calibration and validation, respectively. This showed reasonable and acceptable model performance. The study found that there is poor response of groundwater levels during rainy season which is likely to be due to lack of preferential flows between surface water and groundwater systems. This has resulted in poor relationship between estimated and observed groundwater levels during rainfall season. Key words: ArcGIS, CMB, EARTH, Groundwater recharge, rainfall
Water Use Registration: A reflection of Groundwater Governance of the Verlorenvlei Catchment in the Sandveld	Imelda	Haines	Sandveld	2015	patato, RAMSAR, good governance
Abstract Introduction: Verlorenvlei catchment in the renowned potato Sandveld area is shared by three main towns where agriculture is a primary economic activity. This semi-arid catchment, receives low winter rainfall, but has a dynamic groundwater system providing almost all water services in the catchment and sustaining the acclaimed Verlorenvlei RAMSAR site. There have been recurring concerns of land use as a potential threat to water resources and the sustainability of Verlorenvlei RAMSAR site. The Minister of Water and Sanitation as custodian of water resources requires that surface water use less than 18 250 m3 and ground water use less than 3 650 m3/a to be granted under general authorization. All water use above such general authorization volumes is to be registered (Government Gazette No. 20526 of 1999). Water use registration, is identified as a tool used to achieve the effective management and governance of water resources. Water use above general authorization, is associated with larger scale land use activity, which may have an impact on water resources and the environmental at large. The following study, seeks to examine and compare catchment water use for land uses, to catchment water availability using water use registration data. Comparing water allocation and catchment capacity, this study further seeks to explore the effectiveness of water use registration in achieving good governance of water resources. Purpose: The purpose of this study was to determine effectiveness of water use registration in promoting good governance in the Verlorenvlei catchment Results: Of 124 registered water users identified in the Verlorenvlei catchment, only two of these water users are within the legislative limit outlined by Government Gazette No. 20526 of 1999. Overall, permissible water use is 447 547 259.5 m3/a, over 10 times the catchment capacity of 40 000 000 m3/a. Conclusion: Overall, excessive water use for land use activity is observed within the catchment, despite provision of legislature guiding against excessive water use. Increased water use registration, does however correlate with improved land use practices for agricultural production (Potato SA, 2014) suggesting probability of good governance. Lastly, there is a need for monitoring; improved water and land use efficiency, Integrated Water Resources Management and good governance in the catchment.
Interannual variability in rainfall isotope composition as a tracer of spring water flow.	Roger E	Diamond	Western Cape	2015	Table Mountain Group, springs, rainfall isotopes
Abstract Table Mountain reaches 1086m elevation, the upper half of which comprises Table Mountain Group (TMG) quartzite with extensive fracture porosity. The lower half of the mountain comprises a mixture of Cape Granite intruded into Malmesbury Group metapelites, both of which are poor aquifers, but are in places overlain by scree slopes predominantly composed of TMG quartzite boulders. The region experiences a Mediterranean climate with warm, dry summers and cold, wet winters, with rainfall ranging from 600-1600mm/a depending largely on proximity to the mountain. Several springs issue from the slopes of the mountain, ranging in elevation from 15-410masl and in flow from non-perennial to 30L/s. Water chemistry reveals very little about spring water flow, as the waters have very low dissolved solids. Samples of 10 of these springs were taken twice per year for 3 years while rainwater was sampled at 120masl at the University of Cape Town (UCT) and at 1074masl at the Upper Cableway Station. These samples were analysed for oxygen and hydrogen stable isotope composition, mostly by mass spectrometer, but also by laser spectroscopy. The isotope results reveal an altitude gradient between the two rainfall stations of -0.075?/100m for ?D and -0.48?/100m for ?18O. Employing this isotope gradient, the average recharge altitude for the springs is 304masl, compared to an average discharge altitude of 156masl. Using this difference in altitude and the average slope of the terrain, a typical flow path of 1km from recharge to discharge point can be derived. Additionally, there are shifts in the weighted annual mean isotope composition of rainfall at UCT. For the years 2010-2012, the shifts are paralleled by similar shifts in the mean isotope composition at the springs for each of those years. This suggests rainfall discharges in the same winter season it has been recharged. In combination with the evidence for long term reliability of some of the springs over the dry season and during droughts, this suggests a layered flow of groundwater in the scree aquifer, allowing both long term steady discharge of deeper groundwater, as well as short term discharge of recently recharged rain. In combination with the flow path derived above, hydraulic conductivities in the realm of 10-20m/d can be calculated for the scree aquifers.
Investigation of the probable infiltration from the wastewater ponds and its impact on the water quality of Pleistocene aquifer	EL-Said	Ahmed AL-Sayed Ragab	El Sadat	2015	Electrical Resistivity Tomography
Abstract 2-D Electrical Resistivity Tomography (ERT) and hydrochemical study have been conducted at El Sadat industrial city. The study aims at investigating the area around the waste water ponds to determine the possibility of water percolation from the wastewater (oxidation) ponds to the Pleistocene aquifer and to inspect the effect of this seepage on the groundwater chemistry. Pleistocene aquifer is the main groundwater reservoir in this area, where El Sadat city and its vicinities depend totally on this aquifer for water supplies needed for drinking, agricultural and industrial activities. In this concern, 7 ERT profiles were measured around the wastewater ponds. Besides, 10 water samples were collected from the ponds and the nearby groundwater wells. The water samples have been chemically analyzed for major cations (Ca+2, Na+, K+, Mg+2), major anions (Cl-, CO3-2, HCO3-, SO4-2), nutrients (NO2-, NO3-, PO4-3) and heavy elements (Cd, V, Cr, Zn, Ni, Cu, Fe, Mn, Pb). Also, the physical parameters (pH, Alkalinity, EC, TDS) of the water samples were measured. Inspection of the ERT sections shows that they exhibit lower resistivity values towards the water ponds and higher values in opposite sides. Also, the water table was detected at shallower depths at the same sides of lower resistivity. This could indicate a wastewater infiltration to the groundwater aquifer near the oxidation ponds. Correlation of the physical parameters and ionic concentrations of the wastewater (ponds) samples with those of the groundwater samples indicates that; the ionic levels are randomly varying and no specific trend could be obtained. Also, the wastewater samples shows some ionic levels lower than those detected in other groundwater samples. Besides, the nitrate level is higher in samples taken from the cultivated land than the wastewater samples due to the over using of nitrogen fertilizers. Then, we can say that the infiltrated water from wastewater ponds are NOT the main controller of the groundwater chemistry in this area, but rather the variable ionic concentrations could be attributed to local, natural and anthropogenic processes.
Numerical Modelling of Groundwater Flow Between a Complex Underground Mine and an Operational Opencast Mine	Altus	Huisamen	Mpumalanga	2015
Abstract The management of groundwater inflows into an opencast colliery in Mpumalanga is normally fairly easily achievable due to low inflow volumes and high evaporation rates. But, when flooded underground mine workings are encountered, groundwater inflow complexity increases dramatically. Understanding, predicting and managing groundwater inflow under these conditions can be challenging and highly complex. While normal opencast inflows are easily modelled these connected mines are pushing numerical models to their limits. This case study aims to illustrate an approach based on a finite difference model that has been used successfully in a South African coal mine. Based on a study at a colliery near Ermelo, Mpumalanga, the understanding and conceptualisation of the aquifer geometry, geological structures, hydrogeology, defunct underground mine geometry and interconnection between opencasts and the underground, proved to be vital, not only in calibration of the model, but also in the construction of the various layers and calculation of flow volumes between the various sources and sinks. This also aided greatly in constant source contaminant transport modelling to trace which mining areas may have a contamination effect on each other or the surrounding aquifer. In constructing the numerical flow model, the underground mine geometry was found to intersect various layers in the MODFLOW based model and pinching out in some areas. Due to the requirement of MODFLOW that layers should be continuous with no pinchouts to the model boundaries, this presented a notable challenge in the model construction. Therefore, mine geometry was divided into various slices, fitting within the hydrogeological layers, but still retaining the original geometry. The layers were then further divided laterally using different materials to represent the mine hydraulic properties and aquifer properties respectively, ensuring that the lateral distribution of materials also represents the underground mine geometry accurately. Using this model construction, the calculated mean residual head for the simulation of the current situation was found to be less than 3m while the simulation of the current mining situation with no underground mine present, yielded a mean residual head of approximately 10m. Additionally, inflows measured in the opencast penetrating the underground were measured at approximately 1000m3/d while the calibrated model calculated inflows of 1160m3/d, while simulating the current mining situation including the defunct underground. The current decant from the defunct underground, to the southeast of the site, was calculated as 1.9 L/s by the model while the measured rate was just over 1 L/s. Also, as expected, the dewatering of the opencast penetrating the flooded, defunct underground mine, was calculated to predominantly impact an underground mine compartment, isolated by underground seals, as opposed to the aquifer, which has a much lower hydraulic conductivity. {List only- not presented}
Reliability of laboratory testing of groundwater samples	Venetia	Mitchell		2015
Abstract Resources required for groundwater sampling includes but not limited to pumping equipment, trained manpower and technical resources specific to the sampling function. Bearing these expenses in mind, choosing a laboratory for testing the water samples collected should be a carefully considered purchase. Choosing a testing facility that cannot deliver an efficient, reliable and technically sound service could render the sampling futile. Water samples submitted to a laboratory for testing are received from third party sources more than ninety percent (90%) of the time and sampling techniques and sample integrity cannot be verified by the laboratory. However, the validity, reliability and integrity of the laboratory testing are within the control of the testing facility. These aspects of a laboratory are usually controlled within a quality management system where established policies and procedures form the basis of such a system. This system maintains a foundation for technical competence and customer service at the laboratory. There are numerous testing facilities available to Consultants requiring chemical and microbiological groundwater testing, each with varying levels of integrity and technical ability. It is imperative to maintain confidence in the validity of results of analyses from a laboratory and this assurance can be understood through an examination of a facility's management system. An established quality management system would comprise a policy statement, associated technical methods and technical and administrative procedures. This system would be formally documented and audited as part of the on-going laboratory's management system. In some instances, laboratories formalise this into an accreditation of the laboratory to an international standard, such as ISO 17025:2005. The assurance that the results of analyses from any laboratory are of sound technical integrity would depend on factors such as - personnel training, - accommodation and environmental conditions under which the tests are carried out, - validation of the methodology applied (including the uncertainty of measurement), - the calibration and maintenance of the equipment used, - understanding the traceability of and measurement undertaken, - handling and preservation of the sample on receipt and while in the laboratory. Each of these factors plays a critical role in the integrity of results of analyses and should be interrogated when trying to understand the reliability and competence of the laboratory of choice.{List only- not presented}
Qualitative interpretation of groundwater flow distribution within the southern granite supersite of the Kruger National Park	Ashton	Van Niekerk	Mpumalanga	2015
Abstract Understanding the hydrogeology of fractured or crystalline rocks could be complicated because of its complex structure and a porosity that is almost exclusively secondary. These types of geologies are known to exhibit strong heterogeneities and irregularities contrasted in hydraulic properties, spacing and flow distribution within fractured rock aquifers. Therefore it is important to develop a conceptual model based on site specific data such as the hydraulic roles between groundwater and nearby hillslope/surface water bodies in order to understand its movement within the environment. Therefore this study intends to develop a hydrogeological conceptual model to qualitatively interpret the dominant groundwater flow processes at a 3rd order scale within southern granite supersite of the Kruger National Park (KNP). Key findings based on actual subsurface results in the form of Electrical Resistivity Tomography (ERT) surveys, borehole drilling logs, water levels and hydraulic data suggest that two aquifer types exist on the southern granite supersite namely, a weathered low resistivity of 3-75 ?m (average depth ranging 383-328 mamsl) and hard rock high resistivity of 1875-5484 ?m (average depth ranging 364-299 mamsl) granite/gneiss aquifer. The weathered aquifer flow system responds to localized processes such as piston recharge, indirect surface water recharge and groundwater water discharge via interflow. This was due to the relatively rapid response time of 2-3 weeks in groundwater levels to the major sequence of rainfall events over the hydrological year. The hard rock aquifer is part of a regional groundwater flow system. This is owed to the lengthy response time lags of 2-3 months in groundwater levels to the major sequences of rainfall events over the hydrological year. Due to the generally low transmissivity (ranging 9.50E-08 to 11.2 m2/day) values obtained during the borehole pump and slug tests and inclining trend of groundwater levels after the wet season, suggest these ephemeral hillslope landscapes are likely to act as hydraulic boundary areas. In that they contribute during the dry season to the regional hydraulic head generating baseflow to perennial streams. Therefore from a management perspective certain reaches within these ephemeral streams contribute to recharge which in turn should receive attention as many of the ephemeral stream sand are used for grading tourist gravel roads. Furthermore these granite ephemeral landscapes are characteristic of generally low transmissive aquifer properties and therefore should be given careful consideration before including it in a water supply scheme scenario.
Hydraulic fracturing and Water Resources: Separating fact from fiction	Lizanne	Bredenkamp	Karoo	2015	Shale gas, Dolerite Intrusions
Abstract Shale gas in South Africa can be a game changer for the Karoo and South Africa economy but it may have a devastating effect on the environment. The Karoo communities is highly reliable on groundwater for their stock, irrigation and also for domestic use. Knowing the process and the potential impacts of gas-well drilling and fracturing on shallow groundwater systems beforehand different appropriate studies can be done before any hydraulic fracturing can took place in South Africa. The biggest concerns with hydraulic fracturing is that the fracturing fluids will flow and discharge into shallow aquifers due to the high pressure used or the produced water mixed with deep saline water may discharge into the environment. This paper presents a baseline dataset that will be a reference point against which any future changes in groundwater concentrations can be measured. The Karoo basin with its numerous dolerite intrusions make it unique and different from other countries. These dolerite intrusions are associated with high yielding boreholes because of the fractured contact. The Karoo Basin may be under artesian conditions, which imply that any pollutant might migrate upwards in the Karoo. The understanding of key attributes for characterising groundwater of Karoo Aquifers is most importantly the depth to water level, the yield, and groundwater quality.. The understanding of these characteristics will help to close possible legislative loopholes regarding fracturing. This paper establish an interactive database to obtain full understanding of the hydrogeology of the Karoo to be able to quantify how much water is available in the Karoo and who is the users. Not only the quantity of the water in the Karoo, but also quality and age/origin by making use of different isotopes in conjunction with basic macro chemistry. This will allow for a broader picture before any unconventional gas mining in the Karoo takes place and it can be used to identify any future changes in groundwater quality and quantity of the Karoo aquifers.
Investigating the influence of fine ash leaching in a tailings dam on the underlying aquifers	Paul JH	Lourens		2015	primary aquifers
Abstract Groundwater in South Africa is the most important source of potable water for rural communities, farms and towns. Supplying sufficient water to communities in South Africa becomes a difficult task. This is especially true in the semi-arid and arid central regions of South Africa where surface water resources are limited or absent and the communities are only depended on groundwater resources. Due to a growing population, surface water resources are almost entirely being exploited to their limits. These factors, therefore, increases the demand for groundwater resources and a more efficient management plan for water usage. For these reasons, the relation between the geology and geohydrology of South Africa becomes an important tool in locating groundwater resources that can provide sustainable quantities of water for South Africans. It was therefore decided to compile a document that provides valuable geohydrological information on the geological formations of the whole of South Africa. The information was gathered by means of interviews with experienced South African geohydrologists and reviewing of reports and articles of geohydrological studies. After gathering the relevant information, each major geological unit of South Africa together with its geohydrological characteristics was discussed separately. These characteristics include rock/aquifer parameters and behaviour, aquifer types (primary of secondary), groundwater quality, borehole yields and expected striking depths, and geological target features and the geophysical method used to locate these targets. Due to the fact that 90 % of South Africa's aquifers are classified as secondary aquifer systems, groundwater occurrence within the rocks of South Africa is mainly controlled by secondary fractures systems; therefore, understanding the geology and geological processes (faulting, folding, intrusive dyke/sills & weathering) responsible for their development and how they relate is important. However, the primary aquifers of South Africa (Coastal Cenozoic Deposits) should not be neglected as these aquifers can produce significant amounts of groundwater, such as the aquifer units of the Sandveld Group, Western Cape Province. Drilling success rates and possibility of striking higher yielding boreholes can be improved dramatically when an evaluation of the structural geology and geohydrological conditions of an area together with a suitable geophysical method is applied. The ability to locate groundwater has been originally considered (even today) a heavenly gift and can be dated back to the Biblical story of Moses striking the rock to get water: "behold, I will stand there before thee there upon the rocks thou shalt smite the rock and there shall come water out of it" (Exodus 17:6).
Estimation of evapotranspiration from pine plantations in the Lake Sibayi catchment and its effect on groundwater and Lake level	Mokhadi	Nchabeleng	KwaZulu-Natal	2015
Abstract POSTER Pine plantations require large amount of water for transpirational demand and the amount of water depend on the area of plantation and the rooting depth of plants. The large amount of water required may result in disturbance of the natural water table equilibrium to meet the demand and insure growth. The lake Sibayi catchment area is covered by the 65 km2 freshwater lake sibaya, 70km2 of pine and eucalypts woody plantations and crops. The lake is recharged dominantly from groundwater and it is a water resource for local communities. A large extraction of groundwater by plantations will decrease the water table and the lake level and that will decrease the amount of water available for local residences. The main aquifer is composed of tertiary to quaternary age sediments which form a thin covering which blankets most of the Maputaland coastal plain and rests on a cretaceous system. Shallow marine and beach deposits of tertiary origin overly the cretaceous aged silt, while the quaternary age sediments which constitute most of the cover are predominantly of Aeolian origin. The Uloa formation of tertiary age is identified to be the most promising aquifer in the region consisting of coarse grained shelly sandstone with calcarenite associated with it. The aquifer is approximately 40m in depth and it is recharged dominantly from rainfall through infiltration. Rainfall averages 900mm per annum over the catchment but varies between 1200mm per annum in the south east and 700mm per annum in the west and evaporation equals to ? 1420 mm per annum (Pitman and Hutchinson, 1975). Lake Sibayi is a freshwater lake of 65km2, in surface area and it is a water resource for surrounding communities and other inhabitants. The sandy substrate surrounding Lake Sibayi limit the amount of surface runoff and consequently the water level within the lake are maintained by groundwater recharge. The growth of plantations is influenced by the ability of trees to extract soil water from the intermediate zone below the root zone and the capillary fringe. The water supply depends on the depth of the water table and on the structure of deposited soil layers and the water table depth is determined by the rate at which vegetation extracts water for transpiration and the recharge rate of groundwater. The specific yield of a soil determines the amount of water that percolates to recharge groundwater and because vegetation extracts water from layers of soils above the water table they decrease the amount of recharge for groundwater.
A fresh look at the National Water Balance	Andries	Wilke		2015
Abstract The national water balance is primarily based on the availability of surface water and the historic allocation thereof. The changes that are required the next 20 years to ensure sustainable development of the nation will be painful, but is unfortunately at present not part of the public discussion, it is essentially ignored in favour of more "popular water topics".This paper intends to look at a few core aspects, they include the current water allocation in the national water balance, the relative value of the utilisation, the position of groundwater resources in changing the current relative allocation and the current groundwater utilisation. The paper further intends to be a less formal presentation of these aspects with the required data, references and conclusions available for distribution afterwards.
Contaminated soil and groundwater: Vacuum Enhanced Recovery as an alternative method	Ernest	Rambau	South Africa	2015	Vacuum Enhanced Recovery, hybrocarcon contamination
Abstract Vacuum Enhanced Recovery (VER) has widely been applied in many hydrocarbon contaminated site to recover liquid hydrocarbon from the subsurface Hydrocarbon contamination to groundwater and soil is usually as results of leak or release. Different technologies and method exist to treat contaminated groundwater and soil through hydrocarbon. This paper focuses on the efficiency of VER as alternative method to the site where over 6 000 litres of petrol leaked to the subsurface over a period of time. The application of VER involves creating a capture zone in a particular monitoring well by increasing the hydraulic gradient towards that particular well or set of wells affected by hydrocarbon.
Groundwater and mining on the West African shield: application of mineralogical and weathering profiling	David	Love	West Africa	2015
Abstract The Birimian and Tarkwaian rocks of the Paleoproterozoic West African Shield host some of the most important gold reserves in the world, with Ghana the world's 10th largest gold producer and the region collectively producing more gold than all but five countries in the world. The gold was deposited during successive hydrothermal sulphide alteration events, which were channelled by shear zones and thrusts formed during the regional progressive Eburnean tectono-thermal deformation event. The hydrothermal fluids were auriferous and sulphide-rich, resulting in two distinct types of gold and sulphide mineralisation: (1) gold-bearing quartz- and quartz-ankerite veins, occurring in NNE-SSW trending shear zones or thrust folds, usually in Birimian metasediments, with associated sulphides deposited on the fragmented wall rock and (2) disseminated gold-bearing pyrite and arsenopyrite, occurring in halos within the same shear zones or thrust folds as the quartz veins. The sulphidic nature of the gold deposit leads to a high risk of acid rock drainage (ARD). During operations, inflowing groundwater may carry the ARD into underground workings and opencast pits. Post-closure, as the groundwater rebounds, there is a risk of acidic pit lakes forming or acidic decant of underground mines. However, the occurrence of ARD in such systems can be predicted by a combination of weathering profiling, mineralogical profiling and conventional acid base accounting (ABA). The weathering profile can be divided into three zones, readily distinguishable in borehole core: (i) Oxide Zone, from which both the acid-generating sulphide minerals and the acid-neutralising carbonate minerals have been largely leached, (ii) Transitional Zone, from which the carbonate minerals have been largely leached but the sulphide minerals remain, (iii) a Fresh/Primary Zone, where both sulphide and carbonate minerals occur. The Oxide Zone is generally non acid-generating, the Transitional Zone is acid-generating and the Fresh Zone is potentially acid-generating, depending upon the balance of sulphide vs carbonate minerals. Mineralogical profiles can be prepared from the relative abundance of macroscopic sulphide and carbonate minerals in the borehole core, again providing an assessment of ARD risk. Combined logs can then be prepared from these profiles with acid-generation and neutralisation data from ABAs, illustrating in space where the highest ARD risk zones are located. Using this information, groundwater and mine water management options can be developed for operations and closure, such as prioritisation of open pit backfilling or which levels of an underground mine water should be preferentially excluded from.
Packer Testing and Analytical Modelling For Groundwater Inflow Estimation for Proposed Shafts	Robel	Gebrekristos		2015
Abstract Two ventilation shafts were proposed to be excavated to depths of 100 and 350 m to intersect an underground mine, in the Bushveld Complex. The area is made up of fractured aquifers and the assignment was to identify the exact positions of the permeable zones within the shafts profiles as well as estimate the groundwater inflow rates at every 5 m interval along the shafts profiles. The project was budget and time constrained and therefore the preferred hydrogeological characterisation techniques, particularly the percussion drilling, aquifer testing and numerical modelling could not be conducted. The study was completed by conducting packer tests in HQ sized holes drilled at the exact positions of the proposed shafts. The packer test data was then interpreted using Thiem equation, a modification of Darcy Equation for radial flow, to estimate the steady state inflow rates into the shafts. Transient state flow is more challenging to calculate analytically, as it is time and aquifer storage dependent. However, transient state flow in shafts exists for the first 10 - 15 days only and is short lived. Thereafter, a steady state flow occurs where the rate is nearly fixed for the rest of the life of mine, unless new external stresses, such as mine dewatering, takes place within the radius of influence. Six months later the shafts were excavated and the permeable zones were encountered at the exact positions as predicted using the packer testing. In addition, the inflow rates calculated using analytical modelling was successful in estimating the inflow rates recorded after the shafts were excavated. The packer testing and analytical modelling was therefore effective in assisting the mine to plan the necessary pumps and management plans within the allocated budget and timeframe.
Application of GIS Mapping Techniques to Classify Karoo Aquifers	Mildred	Goes		2015
Abstract POSTER As the National Water Act has evolved to provide for more effective and sustainable management of our water resources, there has been a shift in focus to more strategic management practices. With this shift come new difficulties relating to the presentation of sensitivity issues within a spatial context. To this end it is necessary to integrate existing significant spatial layers into one map that retains the context, enables simple interpretation and interrogation and facilitates decision making. This project shows the steps taken to map and identify key groundwater characteristics in the Karoo using Geographic Information Systems (GIS) techniques. Two types of GIS-based groundwater maps have been produced to assist with interpretation of existing data on Karoo Aquifer Systems in turn informing the management of groundwater risks within Shell's applications for shale gas exploration. Aquifer Attribute and Vulnerability maps were produced to assist in the decision making process. The former is an aquifer classification methodology developed by the project team, while the latter uses the well-known DRASTIC methodology. The overlay analysis tool of ESRI's ArcGIS 10.1 software was used, enabling the assessment and spatial integration of extensive volumes of data, without losing the original detail, and combining them into a single output. This process allows for optimal site selection of suitable exploration target areas. Weightings were applied to differentiate the relative importance of the input criteria. For the Attributes maps ten key attributes were agreed by the project team to be the most significant in contributing to groundwater/aquifer characteristics in the Karoo. This work culminated in the production of a series of GIS-based groundwater attributes maps to form the Karoo Groundwater Atlas which can be used to guide groundwater risk management for a number of purposes. The DRASTIC model uses seven key hydrogeological parameters to characterise the hydrogeological setting and evaluate aquifer vulnerability, defined as the tendency or likelihood for general contaminants to reach the watertable after introduction at ground surface.
A Baseline Study of Scarce Groundwater Resources in Anticipation of Fracking in the Karoo	Divan	Stroebel	Eastern Cape, Karoo	2015	Shale gas, Fracking, sampling
Abstract The anticipated exploration and exploitation of Shale Gas in the Eastern Cape Karoo through hydraulic fracturing has raised considerable debate regarding the benefits and risks associated with this process for both the Karoo, and the country as a whole. Major concerns include the potential impact of hydraulic fracturing on ecological, environmental and especially scarce water resources. The Eastern Cape Karoo region is a water stressed area and with further climate change it will become increasingly so. Thus, effective and reliable groundwater management is crucial for sustainable development in this region. This research aims to hydrochemically characterise both the shallow groundwater (<500m) and deeper saline groundwater in the vicinity of the Shale Gas bearing formations, based on major and trace elements, as well as gas isotope analyses. Sampling will include water sampling and gas measurements from shallow boreholes (<300m), SOEKOR drillholes (oil exploration holes drilled in the 60's and 70's up to 4km deep) and thermal springs (source of water >500m). To-date, a desktop study includes the collation of information determining the areas with the highest potential for Shale Gas Exploration throughout the Eastern Cape Karoo, from which the research area has been determined. This includes the identification of the respective oil companies' exploration precincts. A Hydrocensus has been initiated across this area, which includes slug testing and electrical conductivity profiling of open, unequipped boreholes. Further borehole selection will be finalised from this acquired information. The boreholes will be sampled and analysed a minimum of three times per year, which will occur after summer (April/May) and winter (October/November), after which the hydrochemistry will be analysed. The sampling will be preceded by purging of all inactive boreholes. The possible hydraulic connectivity between the shallow and deep aquifers will be tested, particularly in those areas where dolerite intrusions as well as fault systems may enhance preferential flow of water, using the chemical forensics complemented with passive seismic profiling/imaging and deep penetrating Magneto-Telluric (MT) imaging. The data collected will form a record against which the impact of fracking can be accurately determined. The research is a critical first step towards the successful governance of groundwater in light of the proposed Shale Gas development. In its absence, effective regulation of the sector will not be possible.
Characterise and quantify contamination within the Crocodile (West) and Marico Water Management Areas, South Africa	Chazanne	Allison	Hartebeespoort Dam	2015	Heavy metal, chemical fingerprint, geochemistry
Abstract Define chemical signatures from river waters collected in the Crocodile (West) and Marico Water Management Areas, South Africa. Samples were analysed for anion complexes using Ion Chromatography (IC) and major and trace element chemistry using quadrupole Inductively Coupled Plasma-Mass Spectrometry (q-ICP-MS). Results are used to define the various chemical signatures resulting from activities within the study area which include mining, agriculture, industry, residential and domestic, and recreational usage and to differentiate the 'background' that arises from the natural geological heterogeneity. The aim of this characterisation is to fingerprint the chemical signatures of various anthropogenic activities irrespective of background. Results from this investigation have been mapped using GIS to visualise the data across the study area. Based on the results, the contamination sources within the area can be identified and ranked in terms of their contribution to the total effective contamination received at Hartebeespoort Dam. {List only- not presented}
'Best Practice' Approach To Undertaking Detailed Groundwater Impact Assessment Studies For Proposed Solar Energy Plants	Sheila	Imrie	Jacobsdal, Free State	2015	Solar energy, EIA, best practice, groundwater management
Abstract South Africa is a country at the forefront of the solar energy revolution. Each solar energy plant implementation results in further supply of clean renewable energy to the South African electric grid, thus playing a part in helping South Africa meet its renewable energy targets, in addition to stimulating long-term economic development and creating new jobs. Active solar techniques include the use of photovoltaic systems, concentrated solar power and solar water heating to harness the energy. Particular focus has recently been on the use of concentrated solar power technology which is better able to address the issues of scalability and electric storage. The process includes the use of a liquid salt solution and also requires a reliable water source. When applying for a new solar energy plant, a geohydrological assessment is required to inform the Environmental Impact Assessment. SolarReserve South Africa (Pty) Ltd responsibly take this one step further by requesting detailed geohydrological assessments including drilling and field testing, numerical modelling and simulations, and detailed impact analysis. Of particular consideration in these assessments is the potential for groundwater to meet the plants water needs, as well as the assessment of risk and potential groundwater contamination impact from failure in the lining of the evaporation ponds. This paper describes the 'best practice' approach that has been formulated and undertaken for some previously proposed sites, and is now recommended for future use in the groundwater impact assessment of future proposed solar energy plants in South Africa. It makes use of a SolarReserve case study example, located at the farm Kalkaar near Jacobsdal in the Free State Province, to explain the main steps in the process and how the results of using this approach are important inputs in the assessment of impacts, decision-making regarding go/no-go, technology used, infrastructure and site layout, and responsible management and monitoring of the groundwater in the future.